Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

. . Tool Cabinet: The kids started moving into th

Posts

. . Tool Cabinet: The kids started moving into th

#1

. . Tool Cabinet: The kids started moving into th

Dominic in Buck's County PA

>Hi Gang,

Hi gang,

Over the past week I managed to squeeze in a little shop time. This was no easy feat since I was working a couple 14 hour days! (God bless Caffeine!)

Anyway I moved my jointer, and fore planes into the "plane till". The photo below shows the Tool cabinet with Plane Till door closed.

Photobucket

And this one shows it with the Plane Till door open

Photobucket

I had room enough for my 608, Union No7, 607, Stanley 6C (type 16), 605, 605 1/2C, and 5 1/2 (type 11). I used the same cleats I made a couple months ago. I just moved them from the panel that was hanging above my work bench. I just needed to make (2) more cleats and then I was done.

Since I worked so much OT, I got some comp time and was able to pull off a 4 1/2 day weekend. During that time I laid out the tool holder panels for one door. The panels are 3/16" thk and will fit right inside the door and be mounted to the sides of the box frame doors with screws. The frame is ambrosia maple.

Photobucket

Why the tool holder panel? Well this way I will avoid my fear of driving a screw right through the nice new panel of my door! The holders will be screwed in from the back using counter sunk screws. And if I make it look like swiss cheese after a while, I can replace it a whole heck of a lot easier than a door panel!

At one time this was all laid out using AutoCad. However, several tool acquisitions later I find myself needing to change the layout! I'm working on the layout a bit at a time but I'm pretty sure that this is the one I'm going with. BTW, notice the blank spot next to the Veritas Wheel Marking Gauge? I'm saving room for one with their new mortise marking wheels! (wheee!!)

What do you think of the layout? Any advice?

See ya around,

Dominic

Re: . . Tool Cabinet: The kids started moving into th

#2

Looking good Dom!

Jay in Tx

>'...and several tool acquisitions later...'

Isn't that always to case ;~) Luckily, there looks to be a lot of room left for further acquisition. If it seems packed in the future, just try to think in terms of 'Studley'.

Cheers!

~Jay

Re: . . Tool Cabinet: The kids started moving into th

#3

Re: . . Tool Cabinet: The kids started moving into

wilbur

>Very nice job, Dominic!

Just wondering -- where do you put your chisels? I was Zaprudering the picture, and I seem to find every kind of tool except chisels.

Re: . . Tool Cabinet: The kids started moving into th

#4

Re: . . Tool Cabinet: The kids started moving into

Dominic in Buck's County PA

>Hi Wilbur,

Thanks for the compliments!

They're going on the other door. I have to make a holder and just organize them. Before I do that I may spend some time turning all new handles for them and refurbing them. They are a recent Ebay purchase and need some TLC.

PS I havent forgotten about you stopping over to see the lathe. I just need to talk to the "commander in chief" and clear it with her.

Later,

Domini

Re: . . Tool Cabinet: The kids started moving into th

#5

Thanx Jay!

Dominic in Buck's County PA

>

Re: . . Tool Cabinet: The kids started moving into th

#6

It's looking great Dom!

Scott Burr in Ben Lomond, CA

>Very well organized IMHO. What's in the drawers?

Scott, catching up after a very long 4 day week...:^(

Re: . . Tool Cabinet: The kids started moving into th

#7

Re: It's looking great Dom!

Dominic in Buck's County PA

>Hi Scott,

Thanks for the compliments! As for what's in the drawers, at this moment, not much! One has all my Starrett squares, and another all my blades for my No45 and LV Router. I also have some sharpened "spare" plane irons for my jack planes in there. My chisels are in one. But that's only until I turn new handles for them.

BTW, notice the No46 on the top shelf? Finally go that bad boy out of the box. Now I just have to clean it up and get some blades.

Re: . . Tool Cabinet: The kids started moving into th

#8

Yea, I saw it sitting up there!

Scott Burr in Ben Lomond, CA

>Try Jim Reed for the blades. He makes a great set for it.

Keep us posted and pic'ed!