Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

Panel raiser questions

Posts

Panel raiser questions

#1

Panel raiser questions

Bjenk Ellefsen

>I have this panel raiser and I am trying to understand the beast. There is something I just don't get. It should be simple but something evades me in using this one.

Is it supposed to make the field for me? DO I have to rabbet the field first? I don't get how the iron is supposed to work (look at the pictures). I know how to the use it to slope the panel but something is not right. The profile of the plane shows a field but I don't know how to use it that way.

Any thoughts?


img

Re: Panel raiser questions

#2

Re: Cutter and sole 

Bjenk Ellefsen

>


img

Re: Panel raiser questions

#3

Re: Panel raiser questions

Warren in Lancaster, PA

>This plane looks to me like a moving fillister (rabbet plane with a movable fence). It seems like every thing is made at right angles. A panel raising plane usually has the angle of the raise built in to it.

Re: Panel raiser questions

#4

Re: Panel raiser questions

Bjenk Ellefsen

>No, its not even close to look like a fillister. My fillister is very different. There is an angle, the picture may not show it well.

Re: Panel raiser questions

#5

Re: Panel raiser questions

Stephen Shepherd in the State of Deseret

>I would think it would have a spring line on the front but I can't see on in the photograph. The blade does look like a panel raiser and I would think you would just run the fence along the edge of the board and it should make the cut with the grain. I think you need to cut a kerf, narrow dado or wide rebate on the cross grain as it doesn't have a nicker iron.

Stephen

Re: Panel raiser questions

#6

Re: Panel raiser questions *LINK*

wilbur

>Here's a video of a panel raiser in action, courtesy of Philly Planes, from across the pond.


Philly Planes mini panel raiser in action

Re: Panel raiser questions

#7

Re: Panel raiser questions

MikeW

>It doesn't make the field per se. The portion without the blade acts as a depth stop ontop of the field. Then there is a step down to the bevel--the main portion of the blade.

The fence acts as a limiter to how far in the bevel cuts--the width of the bevel--before the beginning of the field.

Some panel fielding planes such as the one below also have a fence on the side to control how deeply the step is from the field to the bevel.

Take care, Mike


Re: Panel raiser questions

#8

Re: Panel raiser questions

Wiley Horne-- So. Calif.

>Hi Bjenk,

The blade will cut the raised field for you if it detailed right. You do not require a nicker, and you do not require pre-ploughing or pre-rebating to define the field. In fact, if you do, the plane will then be fighting to override what you have already done. As Mike said, you have a depth stop which will define the amount of raise of the field--the little return section of the cutter will nestle down into the raise and give you the correct bevel as the plane bottoms out on the depth stop.

The blade has to be sharp on both main bevel and on the little return portion that cuts the beveled field. When that blade was new, there was a sharp corner where the return meets the long part of the cutter--this defined a crisp break at the raise.

You also do not need to define a flat tongue around the perimeter. Just let the tongue taper, and gauge the thickness by eye or quick check.

Wiley

Re: Panel raiser questions

#9

Re: Panel raiser questions

Bjenk Ellefsen

>Thanks Mike and Wiley. However, in my trial runs with it, I fail to understand how it is going to plow the step by itself. It seems to only plane a field. How would it achieve that even if I hold it at the right angle indicated on the sole... Unless it needs some really thick stock. I'm lost.

Re: Panel raiser questions

#10

Re: Panel raiser questions

Wiley Horne-- So. Calif.

>Bjenk,

We may have a nomenclature problem. I am interpreting 'step' to mean the beveled edge of the raised center portion, known as the field.

First, let's go back to what Warren said. I think he is right in saying that your panel raiser does not have lateral taper to its sole. Some panel raisers have a flat sole, with a beveled step, and with the blade having a bevel-cutting return on it. It's a panel raising and fielding plane. This type of panel raiser is designed this way so that it is flexible in regards to the bevel angle, bevel width, and thickness of wood that you wish to work. You don't have to start with a specific thickness of wood, and you can plane whatever slope of bevel looks best to you. I think that is what your plane does. However, you pay for this flexibility by the fact that you're going to have to tilt the plane to get the bevel you want.

Another basic type of panel raiser is the one shown on Philly's site. It does have a specific lateral slope to the sole. Now with this type of panel raiser, you hold the plane vertical, and keep it vertical throughout the planing. The geometry of the sole takes care of the rest. This is a simpler situation, but then you are dealing with a narrower range of possible geometries and a narrower range of wood thicknesses (in theory, anyway). [By the way, I have Phil's mini panel raiser, and it really is an excellent performer, and came that way from Phil. I ordered the plane because I got green with envy when I saw Mike W's example.]

So what does all this mean on your planet? My suggestion is that you first draw out the profile that you want on the end and edge grain of your board. You won't always need to do this, but it would help in getting started because you'll be able to see your progress more clearly.

Does your plane actually have a spring line? I don't know why it should, because it is designed to be flexible with respect to the bevel angle you can cut. You tilt the plane at the angle you want to put on the panel's bevel section. Start planing, and just as shown on Philly's video, the first cut should take only a narrow strip off the board edge, the second cut should widen and deepen the first cut, and so forth until the full width of the bevel has emerged. You can track progress from your end and edge grain marks. When the bevel is at full width, then the very next cut should begin to define the field. The bevel should begin to sink down below the level of the field, revealing a deeper and deeper field. Stop when you hit your marks, or whenever you're satisfied with the depth of the field.

Troubleshooting: Let's say the above is not happening. Suppose at some point, the bevel you're shaving is deepening at the edge, but not widening and the field is not emerging. One possibility is that you are tilting the plane over more as you proceed, so that the outer edge of the blade is never going to make contact. If the bevel stops widening before it is at full width, then suspect this. However, even if you are maintaining the correct tilt, it could be that the blade reveal is not even all the way across its width, and in fact is not at cutting depth near the outer edge (where the field will be defined). So double check whether you have a good even reveal of blade. One other possibility, if the plane tilt is right, and if the blade reveal is even, is that the blade may be sharpened too steeply, so that it does not have enough clearance angle over towards its outer edge, and can't get a bite for that reason. Or there may be a bump on the sole ahead of the cutter which is preventing the blade engaging the work.

Any of this make sense when you look at your plane?

Wiley

Re: Panel raiser questions

#11

Re: Panel raiser questions

John W

>Bjenk,

I have used both types of planes refered to here and have a couple of pointers based on my experience. One is that on a plane without a nicker iron I score a deep line around the inside with a cutting gauge. For me it isn't worth the chance that there will be no chipping, especially on the ends, against the grain. Second, when you have your bevel established, waste away the excess nearly to the line with a jack or smooth plane, depending on the size of the panel. The Panel Raising irons are tricky to sharpen to the correct angle and can be fussy to adjust in the plane, but once it is set and working it won't have to be touched for quite a while. You don't want to be dulling the iron just removing waste. They are fun to work with, good luck getting yours tuned.

John

Re: Panel raiser questions

#12

Thanks

Jerome Bias

>Thank you for such a clear and precise answer.

Jerome

Re: Panel raiser questions

#13

Re: Panel raiser questions

Bjenk Ellefsen

>Thanks John, sounds like very good tips.