Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Countersinks Explained

Posts

Countersinks Explained

#1

Countersinks Explained

David Miller from Iowa

>Found this in a turn of the century hardware catalog. Many of you probably knew the difference between the countersink types, but I didn�t. I have used them all in wood and none of them in iron or brass.

David


img

Re: Countersinks Explained

#2

Re: Countersinks Explained

Stephen Shepherd in the State of Deseret

>David,

Great post, I knew about the flat one for Iron, I have 4 of various sizes that I mainly use to countersink holes in iron hardware, but I must admit I use it on brass.

I have several snails (the ones for wood) with one or two flutes and they work great.

The one marked for Brass, is interesting. I have a couple of these countersinks, I thought they were for wood, but they don't work that well on wood, so I usually use the snail.

Never get too old to learn something 'new'.

Stephen

Re: Countersinks Explained

#3

source

paul womack

>The one marked for Brass, is interesting. I have a couple of these countersinks, I thought they were for wood, but they don't work that well on wood,

Normally called a "rose" in the catalogues I have.

BugBear

Re: Countersinks Explained

#4

Re: source

Miles

>My experience is that 'rose' countersinks chatter badly and tend to make a polygonal cut rather than a smooth circle. I only use snail c/s now or ones like the 'wood' pattern in this example.

Perhaps rose pattern are OK if you have a very stiff pillar drill and well held workpiece. I think that wood grain tends to start the 'jumping' cut that otherwise happens, giving the poor results.

Someone could make a rose type with irregularly-spaced edges, I suppose....

Miles

Re: Countersinks Explained

#5

facets

paul womack

>The modern 5 or 7 fulte rose countersinks are horrible for hand use, as you say.

But some older ones with large numbers of fine flutes work well - more like rasps or files, I suppose.

BugBear

Re: Countersinks Explained

#6

Re: Countersinks Explained

Bob Demers

>Thanks David

I have all three types on hand, the rose's one being the one I come across the most. The snail type is definitively the better type in wood, hands down, but I never suspected that those three uses (iron, brass, and wood)were what they were designed for.

And now that I see that catalog cut, It really make sense...

Which catalog is that cut from?

Bob, where the snow is starting to be seen thru the Laurentian park

Re: Countersinks Explained

#7

Re: Countersinks Explained---snail????

George in Lowell, Mich

>Okay,

I'll ask the question what is a "snail".

Thanks

George

Re: Countersinks Explained

#8

Re: Countersinks Explained---snail????

Bob Demers

>A slug...:-)

In woodworking, a snail bit is a countersink bit used to accomodate the conical head of screws so that the screw head can sit flush or below the work surface.

Of the brace bit era, we generally find three types of countersink bits, refered to the snail (for wood), the rose head (for brass, but often used on wood. Perhaps by ignorance such as I did before seeing that catalog cut from Peter :-) and the flat one for iron (also known to have been used on wood by sheer ignorantimus :-)

Not sure why its called a snail. Perhaps a reference from the snail shell, the way its made?

In my experience the rose cutter head are the most plentiful, and the snail ones, properly sharpened work beautifully in wood.

Here is a pic of both snail (top) and rose cutter head (5 and 7 flutes one)from my coll..err I mean users assortment :-)

Bob, sleepless may as well have a coffee


img