Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Stanley 289 depth stop

Posts

Stanley 289 depth stop

#1

Stanley 289 depth stop

Bill Houghton, Sebastopol, CA

>Is the depth stop on the 289 identical to that on the 78? I know the fence differs. Is the thread on the fence arm something offbeat?

In case y'all haven't figured out from the questions, I'm watching a 289 missing fence, fence arm, and depth stop.

Re: Stanley 289 depth stop

#2

Re: Stanley 289 depth stop

steve mackay

>Not real sure about the depth stop but I'll watch this thread to find out ! In any case if you can get that 289 for a decent price (and they seem to stay that way sans fence) snatch that sucker ! You'll be glad you did ! You and I can fight over the next fence on Da'Bay latter on !

Re: Stanley 289 depth stop

#3

Re: Stanley 289 depth stop

Don in Northern Arizona

>Bill,

The #78 depth stop will work fine on a #289. The thread is the same, and it fits in the groove on the #289. My #78 depth stop is about 1/16" shorter and 1/64" thinner, but that may be because it is a later model.

Does it have both retractable spurrs? If not they will be hard to come by as they are only shared by #10 1/4, I believe.

Don

Re: Stanley 289 depth stop

#4

Both threads are the same. *LINK*

Don in Northern Arizona

>The fence rod thread and the depth stop thumb screw thread are the same on a #78 and a #289. Of course, the fence rod on a #289 is much thicker, but a #78 rod fits in the #289 thread. You can get reproduction parts for a #289 at the link below. The repro complete fence, rod, and screw is pricey.

Don


St. James Bay Tool Stanley Repro Parts

Re: Stanley 289 depth stop

#5

I just checked mine...And the results are in!

Scott Burr in Ben Lomond, CA

>Everybody here has it right! 78 parts work fine. I've bee bugging Jim Reed to get the set of nickers for them done as well.

Where are you Jim, I know your out there!

Re: Stanley 289 depth stop

#6

Interesting, then, that St. James Bay

Bill Houghton, Sebastopol, CA

>charges almost $5 more for a reproduction 289 depth stop and screw than for a 78 depth stop and screw. Must be some difference in the factory equipment.

Re: Stanley 289 depth stop

#7

Are you sure it's the depth stop and not...

Scott Burr in Ben Lomond, CA

>The fence? The 289's fence is different than the 78's, even though they are interchangeable.

Re: Stanley 289 depth stop

#8

Yep.

Bill Houghton, Sebastopol, CA

>

Re: Stanley 289 depth stop

#9

Finally went for $76

Bill Houghton, Sebastopol, CA

>not worth it. After I assembled a depth stop and fence, I'd be paying at least as much as buying one, and I'd rather spend the money with Rob.

It'd still be fun to have one; just have to examine the rust piles closely when I go garage saling.

Re: Stanley 289 depth stop

#10

Are you sure?

Scott Burr in Ben Lomond, CA

>$80.00 A 289 off ebay

$20-30 for a 78 for parts

$100-110 for a usable plane...

Priceless!

Re: Stanley 289 depth stop

#11

Re: I just checked mine...And the results are in!

Todd Hughes

>The fence for a 289 is NOT the same as one for a 78, is heavier, has equal front and back sections and has two holes for attaching a wooden wear strip and is mounted on a large diameter arm. A fence section for a 289 by itself books for $75- $150.....Todd