Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

Two Questions

Posts

Two Questions

#1

Two Questions

Mike Jurnigan in Suffolk

>I have two questions:

First Question:

I recently purchased from WoodCraft some WoodRiver brand of chisels. They appeared to be well made for a Chinese product. I was not impressed with the handles and wanted to replace the handles with something that is more pleasing to the eye. The catalog write up for the handles state that they consist of a bolster and tapered ferrule. What do I need to consider? When I check where the handle and the chisel meet, on some of the chisels I can see a very fine line on the ferrell where it appears to be two pieces. Is this going to be a major job to replace the handles?

Second question:

Last weekend I purchased a parrie wet stone grinder with out a motor. What should be the proper speed of the wheel? I am guessing 60-80 RPM. Am I close?

Thanks in advance.

Mike in Suffolk, VA.

Re: Two Questions

#2

Re: Two Questions

Bill Houghton, Sebastopol, CA

>Can't help on the chisels. You might talk to Woodcraft.

How big is the wheel on your grinder (did you mean Prairie? Those have a great reputation)? If I recall correctly, the Tormek and Jet grinders run at around 90 rpm. This would be a surface speed of 280 or so feet per minute (diameter times pi [I used 3.14] times rpm). If you assume that's about right for a wet wheel, then 280 divided by [your wheel diameter times pi] should get you a good rpm.

Within reason, I'm not sure you need to obsess greatly, though. Plus or minus 20 rpm's not likely to cause you an issue. Running it at 3450 rpm, like a 6" bench grinder, yes; but not at slow speeds.

I still wish I'd had the money to buy the only one of these I ever saw in the wild - it was a sweet looking little tool.

I own a Delta vertical wheel wet grinder, and have learned that using one of those carbide wheel de-glazing sticks regularly helps a lot. The wheel glazes amazingly quickly. This may or may not be true of all makes of wet wheel.

Re: Two Questions

#3

Rehandling the chisels *LINK*

Wiley Horne--So. Calif

>Hi Mike,

Are these the chisels?:

http://www.woodcraft.com/family.aspx?familyid=5823&mode=details#tabs

First issue is getting the current handles off. You start off not knowing if they're on there by friction fit, or if the whole thing is epoxied together. If these were japanese chisels, you could give the handle a sharp rap on the bench and work it loose with some minor brute force. If it's epoxied, it'll be a pretty big deal involving heat I would think.

Attached below is a link to a photo sequence of So Yamashita rehandling a japanese chisel. This guy is a fine person and a great craftsman by the way. This sequence is instructive as to the general problem, although there are some significant differences.

Here is some pure guesswork--you won't know what's really happening until you get one of those handles off. But it looks to me like the tapered section on your chisels consists of two mating parts. The first is an outflaring of the blade section--this is what they're calling the bolster. Projecting from the bolster will be a tang, which would be maybe 3/4" long or so and maybe 1/4" diameter--check the ones in the link to get an idea. The upper part of the metal taper is the ferrule itself which is wrapping the insertion of the tang into the handle wood. The ferrule butts up against the handle wood above and the bolster section below. You can check if this guesswork is right or wrong by looking for a fine horizontal seam girdling the tapered metal section, where I'm guessing that the bolster section and the ferrule join.

If you can contrive to get the chisel disassembled, and if it turns out to be as I said above, then you can figure out the issues from the link below. You'll have to sneak up on a fit of the wood to the ferrule. And there's no way the pieces are going to go back together perfectly, because the hole you drill for the tang will be off a coupla three thousandths, so you'll need to file the junction where the ferrule meets the bolster section, like So did in the pictures, to make it all come out right.

How do the chisels work? Hope this helps.....

Wiley


Click on 'chisel', then go to 'quince handle' link

Re: Two Questions

#4

Re: Two Questions

Mike Jurnigan in Suffolk

>You are right on the spelling. I picked mine up for $20.00. I could have got it with a motor for $40.00, but the motor was a 3 phase with a variable speed drive and I don't have three phase. The motor I have is about 1/3 hp @1725 RPM. I reckon I will have to rig up a jack shaft to get it that slow.

Thanks, you confirmed what I was thinking.

Mike in Suffolk, VA

Re: Two Questions

#5

Re: Rehandling the chisels

Mike Jurnigan in Suffolk

>That is the set I have. I will try on the chisel that I think that I will use the least. I have some very tight curly maple that will look good on them if I can do it. As I hone them and set them up I will post what I find. He did not mention on the sight about what size hole he drilled for the tang and whether or not he heated the tang before inserting it in the handle. Any ideas on this?

Mike in Suffolk, VA

Re: Two Questions

#6

Re: Rehandling the chisels

Wiley Horne--So. Calif

>Mike,

Interesting point about burning in. This is a typical way of setting a Japanese saw tang in its handle. But I have not heard of this being done with chisels. I'm not an expert at all, so it may be that burning in is sometimes done, but I am sure that a straight friction fit will work.

If you look back at So's site, notice that the chisel tangs are square in section. What the handle fitter does (the handle guy is a different guy than the smith) is drill a round hole for the square tang--the square corners of the tang will then bite into and compress the handle wood. How much clearance he provides will depend on the hardness of the wood species--it would be different for kashi (Japanese white oak, a live oak) than for ebony or one of the rosewoods. You might make a dry run on a piece of the maple scrap and perfect the technique there before drilling your handle pieces. You need to know how much pressure your wood will take before it splits.

Of course, the tangs on your chisels may have a different shape than the japanese tangs. Maybe Woodcraft knows, but more likely you're gonna find out what you have only when you get the handle off, and look at it.

Now If you have a friction fit (as opposed to glue), you should be able to loosen the handle simply by holding the chisel by the blade, and slapping the full length of the chisel down onto a block of wood, or bench. Do that a few times and you should be able to pull the blade apart from the handle with your hands, or with a little assistance from a wooden vise. Note that the handle will not _turn_ if the shank is square, so the pulling has to be directly parallel with the axis of the chisel.

Am pretty sure this is obvious to you, but make the new handles a bit long, because when you start the fitting, if the handle taper turns out to be a bit overdone, and the fit loose, then you'll need to cut a bit off the small end of the taper, and work the taper up higher on your handle blank. Do the fitting before you cut to final length.

To set the new handle, just put the chisel edge onto a piece of wood, and tap the handle with ferrule down over the tang with a mallet. If it closes to within, say, 1/8", and feels right, then hammer it home.

Wiley

Re: Two Questions

#7

Re: Rehandling the chisels

Pam Niedermayer, Austin, TX

>I tried the handle bashing bit on an old, old Japanese saw, at which point the handle proceeded to disintegrate. :)

Why not try to fit the handles while they're still attached to the chisels. You could turn them or use a spokeshave or draw knife. Of course, this assumes that the handles are too big.

Pam

Re: Two Questions

#8

scott grandstaff

Re: Rehandling the chisels *LINK*

scott grandstaff

>Man that was some story. This guy is definitely not working by the hour!

With a shave horse, drawknife and spokeshave he could have been done in 5 minutes flat! A plain round handle? Is he kidding?

It never crossed my mind that anybody could futz around that long with a dowel.

Did you notice the dial caliper? haww ahawww haw!

Here is a link to a little piece to get you going if you want to get into handle carving. It's a whole lot faster and more fun than this guy is making it out to be! A whole lot more fun!! And...Don't forget to put a little style into it!

Oh, and always, always, burn your tangs in. I've tried every possible way and tried it plenty of times, and well, save yourself the aggravation of another split handle. Burn -all- square tangs in!

yours Scott


Old Style Handles

Re: Two Questions

#9

Re: Rehandling the chisels

Stephen Shepherd in the State of Deseret

>I have a few square tapered burn augers that I use for such purposes. This way I do not have to heat up the chisel tang, but can get the burn done with a designated burn auger. Doesn't everyone have one or several?

They are very handy tools, cherry red hot iron drills a nice hole.

Stephen