Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

glazing windows?

Posts

glazing windows?

#1

glazing windows?

James Watriss

>One current project is to remove and replace glass from an old bookcase that has glass doors. I have a few people around here that I'm going to consult, but I figured I'd see if anyone in here had some mystical references for dealing with replacing glass and re-glazing OLD glass doors, with thin frames.

Re: glazing windows?

#2

Re: glazing windows?

steve mackay

>Probably drifting here but . . . I've gotten to where I use points then glue a bead of moulding in. Never had any luck with glazing putty. I've always wanted to goof with it for to long trying to get it perfect. And you KNOW where that leads.

Re: glazing windows?

#3

Re: glazing windows?

James Watriss

>Yeah, I do. Better is always the enemy of good.

Alas, this is a repair job, so I want to do it the "right" way.

Re: glazing windows?

#4

Hi James, Are you talking about...

Scott Burr in Ben Lomond, CA

>Actual putty type of glazing compound? Or are they held in by wood strips?

Re: glazing windows?

#5

Re: glazing windows?

Stephen Shepherd in the State of Deseret

>James,

Is there any evidence of how the original glass was installed? Nail holes, point holes? Was there molding or stops? I would imagine a bookcase would not be putty glazed, although I have restored an 1850's secretary that did have putty glazed lights.

I have seen old glass held in with nails, rather cut off cut nails that passed through the mullion and fastened both lights on each side.

Stephen

Re: glazing windows?

#6

Jim in Burlington Ont.

Soucing the glass

Jim in Burlington On

>Sources for hunting down old glass is a chore. Replacement window guys usually have some. Junk days there might be a window or two out in the trash. Reuse center is another source. New repro glass is mighty expensive. I personally don't mind glazing points and putty. No real tricks to it just make sure to really knead your putty till it's soft and smooth.

Re: glazing windows?

#7

Re: Hi James, Are you talking about...

James Watriss

>I'm pretty sure it's the putty kind. It's an old bookcase, and while I can feel (I think?) some small nails under the surface, there's no sign of a separate wooden piece holding the glass in.

Re: glazing windows?

#8

Re: glazing windows?

James Watriss

>It feels like there are some small nails under the surface of the putty.

I don't think it's going to be incredibly involved, but it's an old glass-doored cabinet, and I wanted to make sure I had all my bases covered before I even took the job.

Re: glazing windows?

#9

Reproduction glass sources

Wiley Horne--So. Calif

>Hi James and all,

Coupla links below. Both provide pretty good visuals, plus samples for a fee:

http://www.clearreproductionglass.com/glass.htm

http://www.bendheimcabinetglass.com/

No financial or other interest etc etc.

Wiley

Re: glazing windows?

#10

Re: Hi James, Are you talking about...

Stephen Shepherd in the State of Deseret

>The glass is probably held with points prior to the application of putty. A traditional formula is whiting (calcium carbonate) and linseed oil made to the consistency of putty. It is a good idea to make it kind of dry and a bit crumbly to work better with the knife.

You can also add a bit of oil based varnish to the mix to help with drying or you can use white lead to speed up the process at some risk. If you can get a good glazing compound that is not an acrylic or other synthetic base, that is preferred.

The advantage of putty is that you can keep at it until you get it right, the corners are the trick.

Stephen

Re: glazing windows?

#11

No direct experience

Bill Houghton, Sebastopol, CA

>The glass I've put in cabinet doors is held by wood strips. I do recall reading a FWW article some years back that suggested tinting the putty to coordinate with the finish, but I can't recall what they tinted with.

Re: glazing windows?

#12

OK James...

Scott Burr in Ben Lomond, CA

>I can't tell if you need to tint the putty or not. I've reglazed many a window in my 10 years of owning my 1935 fixer. It's best to remove the window or door, whatever and work in a horz. position IMHO. Get out all the old putty and make sure the rabbits(?) are clean. The Pratzi remover works well but takes some getting use to. A beater chisel works well also. Prime the bare wood with whatever the need may be. Kneed the putty to warm and spread into the opening. Now here's the important part, use a stiff putty knife to apply the new putty a flexible one will only cause you grief. Mineral spirits are your friend here, to keep the knife from sticking and keeping the putty flowing smoothly.

Also it's easy to smooth out any mistakes, i.e. rough marks by dipping you finger into the spirits to smooth out the putty. The real tricky parts are the corners. It's a bit like sculpting ant that point getting the corners too look good.

It takes a bit of practice, but keep the knife well lubed and you'll be OK.

Good luck!

Re: glazing windows?

#13

Re: glazing windows?

Ron Knapp

>Hi James.

Taking a class that started today on making diamond pane glass doors at Phil Lowes. Phil has seen some doors that used glazing that had turned very hard and was difficult to remove.

The Encyclopedia of Furniture Making (Joyce) shows a few examples using wood so I guess either method would be appropriate.

In the past I've been able to get some 'Antique Glass" at Whittemore-Durgin Glass Co in Rockland MA but I don't know if they still carry it. You might give them a call. I still have some but not enough to do a whole door. Good luck.