Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

A new tote and knob for a refurbed Bedrock 605

Posts

A new tote and knob for a refurbed Bedrock 605

#1

A new tote and knob for a refurbed Bedrock 605

Dominic Greco in Richboro PA

>Hi everyone,

I finally finished those totes I was making for my newly refurbed Bedrock 605. As you may remember, I got this 605 at a flea market for $20. It used to look like this:

Photobucket

Photobucket

The totes & knobs were sanded to about 400 and then sealed with shellac. After the shellac dried I sanded them with 600 grit and then gave them multiple coats of spray lacquer. They were allowed to dry for several days and were finally wet sanded, polished with machine polish, and installed tonight.

These were the first totes I made and they were filled with mistakes. I learned a lot making these and should be better prepared when I make them again.

The plane was cleaned in the usual fashion. Elbow grease and a wire brush wheel. The sole was pitted somewhat near the mouth. Flattening it seemed to get rid of the worst of it. There are (2) small spots near the side rear that are sort of deep. But they shouldn't effect the performance of this plane at all.

Photobucket

Here it is after I cleaned it up and installed the cherry tote & knob. I took it for a test drive on a scrap piece of cherry and was very pleased with the way it was performing.

Photobucket

And here it is with the bubinga tote and knob. Just to give it a real shake down I set the blade to take a very light shaving. You can see the way it handled this walnut.

Photobucket

Of the two, I sort of prefer the bubinga. But I'm not totally sold yet. The cherry is my salute to LN while the bubinga is my knod towards LV. Which of the two do you like better?

Thanks for viewing!

See ya around,

Dominic

Re: A new tote and knob for a refurbed Bedrock 605

#2

I like the looks of the bubinga, but

Bruce, a MN Galoot

>dayamm, man, that turned out nice. Very cool!

Bruce

Re: A new tote and knob for a refurbed Bedrock 605

#3

Hard call

Bill Houghton, Sebastopol, CA

>The darker bubinga looks right, which may be just a matter of what we're used to, but the cherry tote is slightly better shaped, and has great grain. And cherry, of course, will ripen over time.

You're in good shape either way, methinks.

A $20 Bedrock. Geez.

Re: A new tote and knob for a refurbed Bedrock 605

#4

Re: Well...

Glenn Madsen in the SF Bay Area

>A $20 and 12 hours of work Bedrock.

Not that there's anything wrong with that, mind you. Just remember those 12 hours when you go LN shopping...

Nice work here, Dom!

Re: A new tote and knob for a refurbed Bedrock 605

#5

Well done Dom. I like them both...

Scott Burr in Ben Lomond, CA

>The Cherry ones have nice grain and make it look like a LN plane. As Bill said they will darken nicely in time. The Bubinga ones like like their OEM.

You did a great job cleaning it up!

Re: A new tote and knob for a refurbed Bedrock 605

#6

Thanks Scott

Dominic Greco in Richboro PA

>Thanks for the compliments buddy! It was a decent amount of work to make the totes & knobs. But it was worth it. Actually the easiest part was cleaning up the 605! I think I spent about 3 hours total on it.

Re: A new tote and knob for a refurbed Bedrock 605

#7

Re: Well...

Dominic Greco in Richboro PA

>Glenn,

You wrote:

"A $20 and 12 hours of work Bedrock."

Thanks for the compliments! However, I really don't remember saying it took me 12 hours to finish it. I think it took me about 2 - 3 hours total for the plane and about 4 hours for the totes. So that's about 7 hours. But you've got me curious so lets look at the break down.

Lets say that my time is worth about $30/hr (since I'm "unskilled labor". Heh heh!). The wood I got for free but I still needed to cut it up. Lets say $10 for that. Then the finish which was approx $8/can, but for simplicity's sake let's just call that $10.

Labor and materials for (2) totes and knobs:

Labor: 4hrs x $30/hr = $120

Mat'l: $10

Supplies: $10

Subtotal: $140

BUT notice I made TWO sets of totes and knobs. So my cost per set is really HALF the subtotal. Now it's $70

Now lets throw in the time it took me to clean the plane up.

3hrs x $30/hr = $90

And lets not forget the price of the plane itself

(1) flea market Bedrock 605: $20

And just to be picky, lets assume that I account for the electricity I used and the "overhead" of my shop. Let's throw $40 at that.



  • $70 One custom made tote and knob set


  • $90 Labor to clean hand plane


  • $20 Price of 605 Bedrock from Flea Market


  • $40 Overhead and Utilities


  • $220 Grand Total



And unless I miss my guess a LN No5 runs about $280 Plus shipping. So lets say an even $300.

Hmmmmmmm

Now, are my figures for time and material accurate? Probably not terribly so. (Hey, I shot from the hip!) Did I miss something? Most likely, but I think I caught all the major points. :>)

I really went through this exercise to illustrate my point. I totally understand that this is NOT a LN No5. The LN planes are incredibly well made and are in many respects superior.

BUT I took a beat up old venerable work horse of a hand plane and refurbished it to workable condition. I added some custom touches and honed my hand tool skills along the way. And most importantly, I had fun doing it and it makes this plane that much more special to me. So in the end it's like those MasterCard commercials.

Flea Market Handplane: $20

Time and Materials to restore it: $200

Satisfaction of a job well done: PRICELESS

Dominic

Re: A new tote and knob for a refurbed Bedrock 605

#8

Thanks Bill

Dominic Greco in Richboro PA

>Bill,

Thanks for the compliments! I'm thinking that the bubinga will stay on this plane and the cherry set is destined to be installed on my No6C. I think my next set will be made from something darker. Like Walnut, Marado, or Gonsalo Alves.

See ya around,

Dominic

Re: A new tote and knob for a refurbed Bedrock 605

#9

Thanks Bruce!

Dominic Greco in Richboro PA

>

Re: A new tote and knob for a refurbed Bedrock 605

#10

Well... That 3 house payed off IMHO!

Scott Burr in Ben Lomond, CA

>

Re: A new tote and knob for a refurbed Bedrock 605

#11

Dammit I can't spell worth a S&%t today...

Scott Burr in Ben Lomond, CA

>House!?! Hours...

Re: A new tote and knob for a refurbed Bedrock 605

#12

ROTFLOL!!!!

Dominic Greco in Richboro PA

>Scott,

You're killing me bro! :>) LOL!

Dominic