Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

need practice sawing dovetails.....?

Posts

need practice sawing dovetails.....?

#1

need practice sawing dovetails.....?

Bill Tindall, E.TN

>.....build a trunk. I'm getting plenty (and needing every hour of it). 17 feet of dovetail sawing in this trunk I am building. Wrist is sore and saw dull. If I was doing oak trunks for a living I would be buying a bigger heaver saw than the LN dovetail saw. The piece in the PIC is the back panel.

I do a mix of hand and machine work, as well as use the bench for "farm repairs". So the bench is just a big flat surface with vices on the corners. I get around not having the fixtures of a traditional bench by use of clamps. The 2 x 2 clamped to the bench provides support for the piece being sawed. I have problems hitting the back scribe line so I find it faster to used a crutch. I clamp a stick to the back along the scribe line. When I have sawed to it I know the back is right on the line. The 200 foot candles of light I have at bench height comes in handy for following the pen line. I mark with a gel pen. It shows up vastly better than pencil.


img

Re: need practice sawing dovetails.....?

#2

Re: GREAT simple clamping solution!

paul womack

>

Re: need practice sawing dovetails.....?

#3

Re: need practice sawing dovetails.....?

Dean J in MN

>Bill --

How thick are the pieces you are cutting dovetails in? Looks to be 3/4+? In that case, yes, you really want a bigger saw than the LN. I use my carcass saw for cutting dovetails in 3/4+ size stock, the DT saw is really for 1/2" or under. Case dovetails go much quicker with a bigger saw, and the are easier to sharpen to boot!

-Dean

Re: need practice sawing dovetails.....?

#4

Re: need practice sawing dovetails.....?

MikeW

>Hey Bill,

I do something similar for clamping wider boards for joinery. I use a wooden hand clamp on the board which rests on the bench top and another to clamp the clamp to the bench top. The other side, like in your picture, goes into the bench's face vise.

Haven't tried something like you mention for judging the back shoulder line. But hey, always open to other ideas. I'll give it a try for the fun of it!

Take care, Mike

Re: need practice sawing dovetails.....?

#5

Re: GREAT simple clamping solution!

paul womack

>I do something similar for clamping wider boards for joinery. I use a wooden hand clamp on the board which rests on the bench top and another to clamp the clamp to the bench top.

Ah - quite similar to my favourite solution when mortising: but bought forward right to the front bench edge.

Duly noted.

BugBear

Re: need practice sawing dovetails.....?

#6

Re: GREAT simple clamping solution!

MikeW

>Precisely so, BB.

I do the same most of the time doing mortises as well. I do still clamp them at the front edge of my bench simply because I am no longer flexible enough to reach over that far .

And I clamp up at least two legs or whatever is receiving the mortises side-by-side and do them together. So both front legs together, etc. That way I can usually line up the mortises equally and therefore the apron with tenons on each end will also layout equally. They get clamped together at the marking stage so the mortise ends line up.

Take care, Mike

Re: need practice sawing dovetails.....?

#7

2 for 1 marking& chopping a good idea

Bill Tindall, E.TN

>

Re: need practice sawing dovetails.....?

#8

A simple dovetail vise ...

Derek Cohen (in Perth, Australia)

>A simple - and cheap! - dovetail vise may be made from two bolts and metal thread inserts. Add a couple of spinners from scrap. Remove the vise when not needed. All that is visible will be the two thread inserts in the bench apron.



When needing to transfer the marks from tails to pins on long boards, I clamp the pin board in the end vise and balance the tail board on a board clamped upright in the dovetail vise.



A corner clamp is used to hold the two together (BB will love this one!)





Regards from Perth

Derek

Re: need practice sawing dovetails.....?

#9

Great idea, Derek

Bill Houghton, Sebastopol, CA

>

Re: need practice sawing dovetails.....?

#10

Re: need practice sawing dovetails.....?

"RJ" Whelan

>Bill ... I used to have the same problem (re: sawing to the back line).

Many years ago I was in a friend's shop (one of the most skilled cabinet makers I've ever known) and he was sawing dovetails - he had a mirror set up behind the work and it seemed like such a simple aid I gave it a try. I've been using a mirror for over 20 years and probably could saw a DT without it now (still using the original mirror - haven't broken it yet).

RJ

Re: need practice sawing dovetails.....?

#11

Great minds think alike!

Scott Burr in Ben Lomond, CA

>This is how I clamp large boards too.

Re: need practice sawing dovetails.....?

#12

Moses Yoder

Re: no more practice, thank you

Moses Yoder

>I just got done with 9 soft maple drawer boxes. Tired of practicing!

Re: need practice sawing dovetails.....?

#13

You don't want to break the mirror...

Paul M.

>... or you'll have seven years of bad dovetails. ;-)

Re: need practice sawing dovetails.....?

#14

Re: You don't want to break the mirror...

Dan Donaldson

>Gee, when I think of all the mirrors that I have broken....... ;-)

Re: need practice sawing dovetails.....?

#15

Re: need practice sawing dovetails.....?

Derek Cohen (in Perth, Australia)

>Hi RJ

I know that a number of people use mirrors to track the saw cut. I do not bother. I do make sure that I have the outside of the board facing me as I saw. This way I can ensure that the saw does not cut below the line where it will be seen. Does it matter if it goes a mm over the line on the inside where it will not be seen?

Regards from Perth

Derek

Re: need practice sawing dovetails.....?

#16

muscle memory

Andrew F in Australia

>Hi All,

Just further to Derek's comment, I have the baseline of the cut facing towards me, and just cut until the saw hits it. Once you get the feeling of the saw and know where it's horizontal, you're there.

I haven't taught a workshop class in three years, and haven't done much dovetail work, so the muscle memory's a bit sloppy now. The saw could be out of horizontal by about a skinny 1/16th or so over 3/4" (1mm in 20) This is bad enough to cause problems in show work, but, as Derek said, if it's utility work, it's still OK

The speed in your work comes from the muscle memory, knowing where the saw's horizontal and plumb. To cut dovetails (4 pins or so) in a 3/4" board, I used to spend no more than one to one-and-a-half minutes in total on the saw, and about another five minutes on the chisel, tops. It'd be a bit longer now.

Cheers,

Andrew

Re: need practice sawing dovetails.....?

#17

typo: not much dovetail work RECENTLY 

Andrew F in Australia

>