Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Price drop on over 1300 Rockler items

Wood for handscrews

Posts

Wood for handscrews

#1

Wood for handscrews

Bill Houghton, Sebastopol, CA

>I recently picked up some handscrew kits - screws, nuts, handles - at a garage sale for 40 cents each: two each in sizes 2 and 3. I'm seeking advice on suitable wood. The classic wood is, of course, rock maple, but I'm short on chunks of this. I do have some Honduran mahogany, I think in appropriate lengths and thicknesses, and probably some oak (white or red, not sure). Would these work, or do I need to shop around for rock maple?

Bill, hoping this is the Summer of the Shop

Re: Wood for handscrews

#2

I'd go for Oak over Mahogany myself

Scott Burr in Ben Lomond, CA

>

Re: Wood for handscrews

#3

Re: Wood for handscrews

Patrick Gibbons, Somewhere in Texas

>I'm not sure it really matters. The beauty is that you can always make them over again if the mahogany doesn't work out.

Re: Wood for handscrews

#4

Re: Wood for handscrews

Stephen Shepherd in the State of Deseret

>The wood really doewn't matter, I successfully thread pine, what matters is how sharp the tools are, and they always need attention. The V cutter needs to be properly sharpened and positioned so that the threads will not bind in the threads within the screw box.

The dowel to be turned needs to be slightly undersized so as not to bind in the threads in the screw box.

The tap needs to be dressed to remove machining burrs and the edges should be sharp. Drill the appropriate size hole for the particular tap.

You will run into wood of any variety that will not thread well, it is usually limited to the board, so don't dismiss species because your first attempt failed.

Stephen

Re: Wood for handscrews

#5

Depends

Marv....... Northern California Lake Co.

>Hi Bill,

Seems it would depend on what you intend to use the wood screws for.

No. 2 and 3....what diameters are they in inches?

I'm thinking Hickory....same as a lot of handles are made of.

Marv

Re: Wood for handscrews

#6

Re: Wood for handscrews

Barry Turner

>I'd try to go with maple if I could. I think you may find that oak is so hard that it may dent the woods you are clamping if you should happen to bang the handscrews into the wood. Mahogany should work fine, although it seems a bit of a waste to use mahogany for this purpose.

Re: Wood for handscrews

#7

Screws aren't wood, jaws are *LINK*

Bill Houghton, Sebastopol, CA

>The kits I got contain the metal parts for Jorgensen-type handscrews, see link. My question is what my choices are for the wood for the jaws.


This kind of handscrew

Re: Wood for handscrews

#8

Re: Depends

Bill Houghton, Sebastopol, CA

>No. 2 handscrews have 12" long jaws; No. 3 have 14" long. Since most of my other handscrews are No. 1, this was a nice find.

Re: Wood for handscrews

#9

Funny...

Scott Burr in Ben Lomond, CA

>I guess some people just don't read posts completely.

I dug through my stash of maple and I have a few scraps of maple that might fit the bill... Bill. Let me know I'll send you some pic if you really want to use Maple.

Re: Wood for handscrews

#10

Oops, my mistake

Stephen Shepherd in the State of Deseret

>

Re: Wood for handscrews

#11

Now, Scott, be nice

Bill Houghton, Sebastopol, CA

>We've all misread a post and responded to a question not asked. Well, anyway, I have.

Re: Wood for handscrews

#12

Your right Bill...

Scott Burr in Ben Lomond, CA

>Point taken.

Re: Wood for handscrews

#13

Re: Wood for handscrews

Peter Hyde

>Bill I recently made a pair from kits given me by Rob Brophy (thanks again Rob) Mine are the LV ones and you got a real deal. If you haven't made them before you are in for a real brain teaser:-) When it come time to assemble the trick is in starting the threaded rods so that they close the jaws fully and equally then put the handles on so that the rods can't be unscrewed right out of their nuts. My brain hurt so much that I understood why LV had stopped selling them. Now I see they have them again. I used maple for the jaws. The LV kits do come with instructions but it was still a brain strain, I think it's the age thing :-)

Re: Wood for handscrews

#14

"I think it's the age thing"

Bill Houghton, Sebastopol, CA

>Well, THAT's a great comfort. Please tell me you're over 60.

With my recent medical diagnosis, this particular project is likely to be on hold for six months or so, but the information this group has offered will be quite helpful then.

Re: Wood for handscrews

#15

But Bill,hate to tell you this, but...

Scott Burr in Ben Lomond, CA

>Peter is a 14 year old just getting started down the slippery slope. 8^)

Re: Wood for handscrews

#16

Re: But Bill,hate to tell you this, but...

Peter Hyde

>Scott oh how I wish:-) 66 and still able to count:-)

Re: Wood for handscrews

#17

8^) ... you and me both Peter!

Scott Burr in Ben Lomond, CA

>