Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Saw handle repair question

Posts

Saw handle repair question

#1

Saw handle repair question

Dave (Arlington, VA)

>Hi -

I have a English backsaw with a London pattern handle. The handle is missing part of what I believe is called the "lambs tongue." About half an inch of the lambs tongue is missing (and the break on both sides is pretty irregular). I have read various tutorials on how to fix the horn on a broken handsaw handle (and have, myself, repaired broken plane totes and made saw handles for other saws) - but I am not sure how much of those experiences are applicable to this. This seems particularly challenging - especially getting the two sides to meet so you can get good glue joint on both.

Anyone with any experience in these kinds of repairs that mind sharing any pointers?

Regards -

Dave

Re: Saw handle repair question

#2

Re: struggling...

paul womack

>The handle is missing part of what I believe is called the "lambs tongue." About half an inch of the lambs tongue is missing (and the break on both sides is pretty irregular).

I'm struggling to visualize this - any way you can post a picture?

BugBear

Re: Saw handle repair question

#3

Re: Saw handle repair question

Derek Cohen (in Perth, Australia)

>Hi Dave

I agree with BB - need to see it.

In the absence of a picture, I will take a stab anyway.

Hopefully you can cut away the section of the offending lamb's tongue in one piece. Aim to do so such that one side is narrower than the other (either "vertically" or "horizontally"). In other words, to facilitate a tapering replacement wedge. That way it can fit and snuggly on all edges. Then fretsaw, rasp, file and chisel until there is a match.

Regards from Perth

Derek

Re: Saw handle repair question

#4

I would like to see a pic also, but...

Alan DuBoff

>It sounds as if there is a section missing between the tip of the tongue, along the carved base...I'm referring to an article written by Phil Baker, he refers to the lamb's tongue as the "carved base", and where the tongue goes up and over, as it starts to go down Phil refers to that as the "lower ogee curve".

If your handle is broken as I think it is, in the middle of the tongue, I would think you would be better off removing the tongue tip and piecing the entire end of the tongue. I think it would be much more difficult to get a good glue joint on both sides of the tongue. Without seeing how the tongue is in relation to the cheek would determine how to fix it.

To replace the center section, a scarf with 45 degrees would be my choice, where the pieces overlap.

At least that is what I would do if I understand you correctly. With a scarf you can get a decent purchase with a small clamp,

Would like to see pics of it anyway, those are my favorite handles. Some had large chamfers on the shoulder at the top of the cheek, I like those. The Groves & Sons are often like that.

Re: Saw handle repair question

#5

Re: Saw handle repair question

MikeW

>Hi Dave,

I personally would replace the handle--but that too has challenges.

If I were to do this repair, I would most likely replace the entire tongue as seen in the drawing below. I would try to patch in a little piece as it would most likely not last long.


Also, note how far the slot for the blade enters the tongue. You would need to saw that in after repair, but the existing kerf will guide the saw.

The shaping of the tongue were it joins the cheek is easily accomplished with a narrow rasp or rifflers followed by a small half-round file. A course 8" half-round file followed by a fine 6" half-round would also work.

Take care, Mike

Re: Saw handle repair question

#6

Re: Saw handle repair question

Marv....... Northern California Lake Co.

>Hi Dave,

If you can do what Derek is suggesting using a wedge type cut, that is the best way to go because you won't need to clamp it. Just tap it in tight with glue on all surfaces. Take your time and get a good match with the angled cuts. And be aware of how the grain in the new wood lines up with the old wood in the handle. Take pictures of both sides for reference so you can get the carving the same as original or perhaps you have another saw handle to compare to.

If the break won't allow a wedge type repair, cut the old wood off so you end up with a flat surface that will be clampable from top to bottom. I have cut off the entire bottom of a handle just below the bottom screw to make this type repair.

Make it a fun thing,

Marv

Re: Saw handle repair question

#7

I'LL TRY TO POST A PIC... and thanks

Dave (Arlington, VA)

>Hi -

Sorry. I thought I had posted a reply earlier, but must have forgotten to hit the "post message" button.

Thanks to those who posted replies and I can sympathize with the difficulty in visualizing my problem based on my prose description. I will try to post a pic...however, I am computer inept and it may take a little bit of time for me to figure out how to get the pic out of my digital camera and post a copy of it here. My wife if the camera master in our family.

Again, thanks to those who provided some helpful thoughts even without pics, and I probably should have anticipated that it would be much easier to provide comments if you could see the actual condition of the saw.

So, I'll give the pics a try and hopefully will be able to post them in the next day or so.

Regards -

Dave

Re: Saw handle repair question

#8

Re: I'LL TRY TO POST A PIC... and thanks

Dan Donaldson

>If you have problems either getting the pictures posted or getting them sized and not too small to see, send them to me and I will fix them for you.

Re: Saw handle repair question

#9

Re: I'LL TRY TO POST A PIC... and thanks

Dave (Arlington, VA)

>Thanks, Dan. Very kind of you to offer.

Just getting in from work ;-( and an early morning planned. So I won't be able to get to it tonight. I hope to try tomorrow evening.

I very much appreciate the offer.

Regards -

Dave