Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

Finished the joinery on this piece today...

Posts

Finished the joinery on this piece today...

#1

Finished the joinery on this piece today...

Stephen Shepherd in the State of Deseret

>I still have some work to do on the rockers, some chamfering and I will glue it up. I still need to make slats with a 1/2" between for ventilation but I will nail those in place after it is painted.

It was a fun project and took about 16 hours not counting the turnings, had my apprentice do them. Have a couple more hours and it will be done. It is based on a couple of traditional designs.

Stephen


img

Re: Finished the joinery on this piece today...

#2

Re: Finished the joinery on this piece today...

John H. in Baltimore

>Very nice!

I'm embarking on a similar project and would like to know how you designed the M&T joints at the head and foot of the cradle. I plan to provide space for expansion/contraction in the top mortises. Does your design provide for wood movement (or is it small enough to not be a concern)?

Thanks for posting this!

John

Re: Finished the joinery on this piece today...

#4

Nice paint job, it looks like pine brush marks!

Alan DuBoff

>

Re: Finished the joinery on this piece today...

#5

Re: Finished the joinery on this piece today...

Stephen Shepherd in the State of Deseret

>John,

The wood is very dry (air dried) and it is quite dry out West, so I didn't allow for expansion and contraction, but I din't think it will be a problem because of the small size and the double mortices.

The mortices are square, I could have angled them but I didn't, they are not that deep. The tenons were cut at the required angle with a single cheek on the outside. The head board and foot board have cut outs (cupids bows) and I think the cut out will help. I have also added some matching chamfers on the upright posts.

I cut the head board and footboard to 5 degrees, cut out the cupid's bows and sawed each of the tenons to fit the mortises.

Stephen

Re: Finished the joinery on this piece today...

#6

Re: Finished the joinery on this piece today...

L. Hanson

>I see where you used your ellipse engine! Thanks for the photos, it looks great - a classic design!

Leif

www.norsewoodsmith.com

Re: Finished the joinery on this piece today...

#7

The Ellipse Engine performed....

Stephen Shepherd in the State of Deseret

>flawlessly and I was easily able to set it up to do any part of an oval I need.

I am going to post a video of the Oval Making Machine or Ellipse Engine, in use on my blog soon.

Stephen

Re: Finished the joinery on this piece today...

#8

Jack Guzman from Maine

For now....

Jack Guzman from Maine

>..would you have a picture of it? Ellipse engine? Never heard the name before.Is it something you invented or a reproduction of an old tool?I'd like to hear more.I must have been absent that day.

I really miss the chats, but my day starts at 4 AM these days and ends at 9PM. Even if I logged on I'd fall asleep during the chat.---Jack

Re: Finished the joinery on this piece today...

#9

Re: For now....

L. Hanson

>Look on Stephen's blog page fpr a photo of his "ellipse engine":

Re: Finished the joinery on this piece today...

#10

link....

L. Hanson

>Here's the link... it obviously didn't make the last post

http://www.fullchisel.com/blog/?p=70

Re: Finished the joinery on this piece today...

#11

Video *LINK*

Stephen Shepherd in the State of Deseret

>Here is the video I shot today showing how it works, it is on my blog.

Stephen


Full Chisel Blog

Re: Finished the joinery on this piece today...

#12

1/2" seems big

Bill Houghton, Sebastopol, CA

>fine for ventilation, but it seems like enough for a baby to insert fingers and get stuck. Is this because it's historically correct?

Re: Finished the joinery on this piece today...

#13

Re: 1/2" seems big

Stephen Shepherd in the State of Deseret

>Bill,

1/2" or slightly larger is what I have seen in most traditional cradles of this period. I have seen ones with solid bottoms as well. There would be a tick in the bottom and blankets, &c., so I don't think it is a problem.

The spacing on spindles is 'street legal' as they are 4" OC, but so were the old ones, so just copying what already is there.

I think ventilation and drainage is important, I have repaired a couple of old cradles that had damage to the slats.

Stephen

Re: Finished the joinery on this piece today...

#14

Re: The Ellipse Engine performed.... *LINK*

paul womack

>Apparently the design is rather old, sometimes called the "trammel of Archimedes"; I've not heard it called an "ellipse engine" before.

I think "elipsograph" would be more conventional.

BugBear


animation

Re: Finished the joinery on this piece today...

#15

Re: Finished the joinery on this piece today...

Chris Friesen

>I've always heard that there were standards about baby cribs...things like not having vertical projections that could suffocate a child if their shirt caught on it, not having gaps big enough for a baby's head to fit through, etc.

Do you think these are not really factors of concern?

Re: Finished the joinery on this piece today...

#16

Re: Finished the joinery on this piece today...

Stephen Shepherd in the State of Deseret

>Chris,

No, I do think those things are important, this is for a museum and will probably not be used. I don't know how I can design it any safer, it has kickers on the rockers so it can't readily tip over.

The spacing between the spindles is 4 inches, which I think is the requirement. The small openings might be a problem and if I make any for resale, I will have to include a disclaimer.

Stephen