Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

My first split-nuts for a handsaw!

Posts

My first split-nuts for a handsaw!

#1

My first split-nuts for a handsaw!

Alan DuBoff

>These are the first 2 split-nuts I made, out of bronze. Although most people use brass split-nuts, bronze is more durable and much more resistent to corrosion than brass when put into the elements.

Slotting could prove tricker for the backs, since bronze is much harder and more difficult to work with, but the 932 seems to turn nicely. I love the color, it has a pinkish tone to it, opposed to the brass.

2 split-nuts on the left are the bronze ones I made, the one on the right is one turned from Alloy 360 which I bought from a machinist.

You can see the wood grain reflecting in the bronze face.


img

Re: My first split-nuts for a handsaw!

#2

Moses Yoder

Re: My first split-nuts for a handsaw!

Moses Yoder

>I am looking at those and wondering how much a set of three would cost me. I imagine you spent hours making these. They look great. I imagine the bronze would be harder than brass but am not sure how it compares.

Re: My first split-nuts for a handsaw!

#3

Re: My first split-nuts for a handsaw!

Derek Cohen (in Perth, Australia)

>Hi Alan

Those look terrific. Really excellent. As good as anything I have seen. I think that Mike had better watch his back! :)

What was the process?

Regards from Perth

Derek

Re: My first split-nuts for a handsaw!

#4

Re: My first split-nuts for a handsaw!

Tony Zaffuto

>Alan,

Are you a trained machinist or are you self taught? Either way, those are gorgoeus!

The reason for my question is that I am contemplating a samll metal lathe for my shop.

Tony Z.

Re: My first split-nuts for a handsaw!

#5

Re: My first split-nuts for a handsaw!

Alan DuBoff

>I don't think it would be profitable for me to do that, yet. These were turned on a friend's Hardinge lathe and the slots and squares were milled on a full size Bridgeport mill. When I have my lathe setup (small South Bend 9A) and my Nichols horizontal mill running (it's close, just got a motor for it), it might be possible to make some and sell to folks like yourself. I have another smaller mill, and the South Bend is very close to operational, that might be adequate, but it would still take some time to make them. Hard for me to calculate off these first ones, it required working through the problem, and working it out, and that took time that wouldn't normally be spend on the process. However, bronze cost is much higher than brass. Especially for the backs. The back stock cost about 5x the price of brass, about $10/ft. vs. $50/ft. In the case of split-nuts it is mostly labor, and not very much for the material (maybe $1-$2 per split-nut), but in the case of the back, it's much higher, and if you have to cut an odd size and end up with 4" of bronze stock, that is costly also...because you can't use it for anything useful.

Bronze is way better, and IMO, a much nicer alloy. There are different types of bronze, this is 932 which mills nicely. 954 is much more yellow I'm told, but haven't bought any yet, it is much harder and more difficult to mill, and possibly not as desirable color wise since it is very close to brass. As the light changes on the 932, it throws of a wonderful pink hue. This is nice stuff to mill...I could get hooked on it...but then I cut some wood, shake it off...and I'm back! :-)

Re: My first split-nuts for a handsaw!

#6

Today is my lathe's birthday! *LINK*

Alan DuBoff

>Tony wrote:

"Are you a trained machinist or are you self taught?"

Are you serious? I know very little about machining, and just bought my first lathe recently. These were done on a friend's mill and lathe, he was showing me how to do it, and while I milled most of these, the idea was to show me how to do it so that I could do it at home on my little South Bend.

Funny enough, my lathe is having a birthday today. April 12th, 1946, it was shipped to the Levi Strauss & Co. factory in San Fransisco...I might get it running this weekend, I have to bolt it to the bench, and hook up the counter shaft and motor. How cool would that be on it's birthday???? :-)

And to further answer you question, I didn't have hardly any machinist tools until recently, like 2 days ago...I bought a toolbox of machinist tools from a retired machinist who worked at the Caterpillar plant as a tool and die maker for 35 years. He did me a big favor in selling me his tools, for only $500...since I'm not a machinist by trade, I have no idea how much they're worth, but there has to be several thousand in tools, easily...since it's my lathe's birthday today, I'll link to it.:-) Happy Levis to you...Happy Levis to you...Happy Levis to my South Bend, like an 'ol pair of blue jeans...:-)


img

South Bend 9A, April 12, 1946 ship date

Re: My first split-nuts for a handsaw!

#7

Mike has no worries...

Alan DuBoff

>Derek,

At the pace I get things done, Mike has no worries...it took the contest for me to get a saw completed...:-/ The way you word that is as if I would stab him in the back...I hope that would never be the case. I consider Mike to be one of the best saw makers going. He has helped me to do things that he does for his business. My hat is off to him for all his help and advice.

I have some ideas that I would like to try myself, I don't want to be like Mike, TLN, Adria, Grammercy, or any other saw maker of our day...all of them make great tools, I just have some different ideas for saws, to make them unique.

Bronze is not for everyone, it costs way more than brass, a small mistake can be costly. It is a lot more durable than brass though, and way more resistant to corrosion from elements. It is also beautiful in how the pink hue sparkles off of it as the light changes. I happen to like it a lot, but it's not for everyone.

Re: My first split-nuts for a handsaw!

#8

Re: Today is my lathe's birthday!

Tony Zaffuto

>Well, Alan, your post is an inspiration to the rest of us. I own a manufacturing plant, with a very complete tool & die shop. However, you know the old adage about the carpenter never getting work done in his own house? Well, that is nearly the case when I want a tool of my worked on by one of my machinists!

I've been toying for some time to purchase a small lathe and mill for my home shop. I'm kicking myself in the butt for a small lathe I let go of a few years ago (Shelton???, like a small South Bend, also about 60 years old). I do have a small table (36" width) Bridgeport mill that is no longer used. Issue would be getting it into my basement shop!

Anyhow, I'm not trained in any metal work whatsoever, and my holdback to purchasing a small lathe is wondering if it would sit idle!

T.Z.

Re: My first split-nuts for a handsaw!

#9

I only get things done through persistence! *LINK*

Alan DuBoff

>Tony,

Only you can determine if you will use a mill or not. Yes, a lot of people buy tools that sit and do nothing. I often by those from them...;-) Some people have what it takes to use them, others don't. It is no different than woodworking tools, just at a higher buy-in, since machining requires mostly specialized tools. Seriously, when looking at mills, most people want something they can have in their home, and there are not a lot of great options on small mills, unless you get an import. Clausing made some that are bench top and/or base type mills, but hard to find as they operate on 120v, the 8520/8525/8530 series. Those are slightly smaller than a Bridgeport. Also, there was some slightly smaller Bridgeports, I think like a 42" table, but those are more desirable due to size. I am trying to get an old Nichols horizontal mill together, and it takes substantially less space, but it still weighs 1200#, most is not light. So, yes getting mills and lathes down into a basement can be challenging, but I've seen some clever things and it can be done. I've seen people hoist them down on ramps with winches on their trucks...

I don't know how inspirational I am, I tend to jump off on tangents and want to learn and do everything when I create something. Hence making my own split-nuts and even out of bronze, that is me.;-) Sure, most machinists tell people like me that we don't know parts of our body to a hole in the ground, but I tend to stick my tongue out at folks like that, if for nothing else but to antagonize them.;-)

My ambition to learn metalworking is purely in regards to making tools, mostly for working wood. Working wood is my real love.

I'm just a hack, honestly, you must have real machinist working for you...check these tools out I bought recently, from what appeared to be a real machinist. So fascinating digging through the toolbox, old conversion charts, specialty tools, measuring tools, mills, taps, reamers (over/under, dowel pin, in sets), height gage, test indicators, dial indicators, mic, transfer punches, more reamers, and taps in spiral-flute, 2-flute, 3-flute, 4-flute, drill bits, die grinder, bore gages, radius gages, screw transfer punches, etc...

There's a life story in these tools, a man spent 35 years as a tool & die maker at Caterpiller...this will help me with my toolmaking, no doubt. This pic is of the tools out of the box, but check out the linky for more detailed pics of what is in the drawers. I bet he felt bad as I drove off with his career, but as I told him I will not be selling them, I plan to use them and leave them to my family one day...*wink*

As I said, I am not a machinist, he might have really taken me to the cleaners by charging me $500 for them...but I know a little more than zero, and not one to spend my money foolishly! *grin*


img

Machinist Tool Acquisition Linky

Re: My first split-nuts for a handsaw!

#10

Re: My first split-nuts for a handsaw!

Alan DuBoff

>Derek wrote:

"What was the process?"

I wasn't trying to avoid the question, others have shared with me how they have done things, so I thought I would describe to you what is needed to be done to create one of these split-nuts, for a bolt and a washer.

First you buy some bronze stock the size you need, and I wasted some as I made 1/2" heads/washers out of 5/8" round rod, but I wanted to make sure I had enough to take it down, you want the size to fit nicely in a common forstner bit, and the 2 most common sizes are 1/2" and 9/16", but Mike uses larger medallian types, those are very nice. Mike has his professionally done and doesn't bother with any machining for stuff like split-nuts. AFAIK, Mike uses all brass, as does most other vendors. I'm sure most saw makers would have a hard time justifying using bronze for saw backs and split-nuts, but I'm not like most.*wink*

Anyway, it goes something like this...turn the stock down to a known diameter, most of it is going to be cut off, so a rough cut is probably ok, but we did some testing, this was design as we go, kinda like the "by the seat of your pants" approach...*lol*

Once down to 1/2", the bolt portion portion was cut down, 100 thou at a pass, so it took about 5 passes to get down to 3/16", but later we would learn that it's better to go with .190, and .01875 I think is 3/16. It will work, the thread will just be slightly shallower, lesson learned. As it turns out, 10-32 is the size used on the one I used as a model, JohnnyK turned it and it's Alloy 360.

The area to be milled square was left full size, would mill that down soon...but before that I threaded the bolt end, manually but using the lathe to hold/position the work. As I threaded, I moved the tailstock in with a chuck in it, opened so the jaws would provide square threading on the die wrench. A typical small tap wrench handle was used. We just kinda did it by eye on how much we would need. Now, a small bevel was added so the head will drop into a forstener hole easily, then parted from the stock, and that would be ok, but we put the bolt into a 3/16" collet and took 2 thou off the top to clean the face up, pretty high speed at 4000 rpm, with a really slow feed rate. Gave a nice finish.

Now take that to a mill, and put the bolt into a collet and mill down the squares, using a square index block, these are pretty common, although I don't have one I used my friend's. *wink*

Flip the 4 sides and link up the indexing block to the vise, and square the section that will push into the handle and hold the head side from spinning. We know that is in theory, many saws have spinning nut heads in them...;-)

Go back to the lathe, and use the same round rod turned down to 1/2", give or take a nat hair...:-/ drill the hole needed for a 10-32 tap, I think it's a number 30 or 31, by using the tailstock and a drill bit inside a drill chuck. Tap the 10-32 hole similar to how the bolt was threaded, but using a tap with small tap handle and using the lathe to line it up and turning the spindle by hand.

Cut the bevel for the washer, part it off the stock.

Now, this part is a bit tricky, and another way could be done to change this, but I have a small holder/fixture to handle this. We created a small holder/fixture with a 1/2" hole milled in a piece of aluminum, the washer was put in with the side to be slotted, and the 1/2" end of the stock was held in the end while the mill slotted it with a .32", this is actually a bit smaller than I would like...but my friend had a slitting blade too small, one too large, and that meant the .032 (I think the size) was just right! *wink* I'll widen that a bit in the future.

One other step we did was to mount the washer in a collet using an interesting contraption that allowed positioning to a specific depth, kinda like an adjustable bolt through the collet, fitting on the back of the collet...very slick, and we turned a thou or two off the washer face. I wouldn't bother with this part, IMO, you will file it down later after installing.

Although done on my friends mill and lathe, this is all stuff I can do on my equipment in my garage, and one of the main points of this excercise. Sure, I have to get some of it running, but hey, that's all a part of the fun, right?

Hope that explains it clearly, it's probably clear as mud.

Re: My first split-nuts for a handsaw!

#11

Re: I only get things done through persistence!

Tony Zaffuto

>Alan,

Nice haul on the machinist tools. I believe you got your money's worth. I made a similar buy about a decade ago, included a Gerstner box, loaded with mic's, calipers, radius gages and on and on.

My now deceased great-uncle was a woodworker who became a very good machinist. In our part of PA (North-west central), there was a saying here that went "The best machinists were ones that started as carpenters or was it the best carpenters were ones that started as machinists".

Anyhow, I'll figure out how to get the mill and a lathe into the basement, or possibly have to clean the shed attached to the garage out and put it there. Seeing the split nuts you made has started me on another slope!

Tony

Re: My first split-nuts for a handsaw!

#12

62 years, on the money, it spins back to life!

Alan DuBoff

>Tony wrote:

"Nice haul on the machinist tools. I believe you got your money's worth. I made a similar buy about a decade ago, included a Gerstner box, loaded with mic's, calipers, radius gages and on and on."

This was one of the best things I did in regards to tools. It will save me so much money, and there are so many tools that I will be able to reuse. Some great tools that I wouldn't have even bothered to bought most likely, so it was good to get a package like that. I was bummed slightly when finding my lathe, as I would rather had found one with a boat load of tooling. Finding all these machinist tools at an affordable price just balanced things out for me. Alls well that ends well, as they say.

It was 62 years, on the money, that my little South Bend 9A spins up to life once again, for the new owner (ME! :-). It was shipped from the South Bend factory on April 12, 1946, and spins up to life for me on April 12th, 2008.

I wonder if my lathe can collect social security, being 62 and all...:-/

Re: My first split-nuts for a handsaw!

#13

Also consider the Rusnok if tight on space! *LINK*

Alan DuBoff

>Tony,

Was gonna reply last night, as it got late (imagine that...actually it got early...early of today...:-/) but wanted to say that if space was tight and you were looking for a quality small mill that could create woodworking tools, the Rusnok is not a bad option.

A friend has one and loves it, real quality machines, but only for small parts.

This would be capable of making most woodworking tools, hand plane parts, custom plates, etc...and not take up the space of a Bridgeport. As you know, even the small ones are BIG on most people's standards.

You could carry a Rusnok into your basement also, much easier than you could get the Bridgeport down there. And, you could sell your Bridgeport fairly easy most likely as it is desirable being small. Silly me, I thought 42" was small, most I've seen are 54" I think.


Rusnok Mill

Re: My first split-nuts for a handsaw!

#14

Nice nuts...

Scott Burr in Ben Lomond CA

>I've heard of brass balls, but bronze nuts!?! Better not go there...

You chose bronze because it's corrosion resistent. Please tell me your not going to use that saw you made oustide in teh acid rain, are you?

Re: My first split-nuts for a handsaw!

#15

Re: Nice nuts...

Alan DuBoff

>Scott,

I use my tools wherever they need to be used, if I have to do woodworking out in the acid rain, I guess I would use them there...:-)

I just think it's a better material to use, it is stronger than brass, it looks way cool with the color hue with light, and it is more corrosion resistant. All in all, this adds up to a better material, IMO.

The back is more concern, cost wise, as the cost of a bronze back is way higher. Hard to put a cost on one's tools, though. I prefer my tools be made out of the best materials I can use, certainly for myself.:-)

I have brass, and I can use it also, but this bronze is way cooler...for my taste.