Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Shop oak flooring attachment method question...

Posts

Shop oak flooring attachment method question...

#1

Shop oak flooring attachment method question...

John Aniano in NJ...

>Hello All,

I'm about to install 400 square feet of 5-inch wide, tongue & groove, T&G end matched, white oak flooring to my new shop floor. The subfloor for the second storey shop is 3/4" thick T&G plywood over 2x10 floor joists on 2-foot centers. There won't be any heavy machinery in this 2nd floor shop, only a workbench and tool cabinets. The floor isn't "springy".

The oak flooring was bought last summer and has been sitting stickered in the building (unheated) since the summer. The shop is a passive solar design and is very well insulated (~R30) on all sides, floor, ceiling, and walls. I expect to put maybe two coats of a matt polyurethane as a finish, keeping the white oak light color.

My question is this: should I staple and use construction adhesive to glue the floor to the plywood or use red rosin paper and staple through the paper to the subfloor? I have gotten mixed messages on both methods, i.e. floor will buckle, too much seasonal movement, etc. I want to do it so it will stand up to shop use, but don't want to do it twice. Any thoughts or personal experience would be appreciated.

John

Re: Shop oak flooring attachment method question...

#2

Re: Shop oak flooring attachment method question..

Bill Tindall, E.TN

>There are professional flooring installers that hang out on the main message board. This topic has come up before over there. Check archives or repost over there. I don't see that this installation is any different than a residential floor. I would have picked narrower boards for this application. I would apply three coats of finish, with the first thinned some. If the finish is robust it will absorb the abuse and be easily renewed as needed.

Re: Shop oak flooring attachment method question...

#3

Rosin & Staples

David Miller from Iowa

>In my mind, floor adhesive is best used in attaching the subfloor to the joists - I don't see any advantage in gluing the floor boards to the subfloor.

David

Re: Shop oak flooring attachment method question...

#4

Re: Shop oak flooring attachment method question..

Stephen Shepherd in the State of Deseret

>John,

If you have the time, staple down the rosin paper then lay the floor loose without nails, staples or glue and let it sit for a year or two.

Make a couple of basswood folding wedges to wedge it tight together. If it swells the basswood wedges will compress and if it shrinks you can tighten it up.

After a year or two you can nail it down with no problems.

Stephen

Re: Shop oak flooring attachment method question...

#5

Re: Shop oak flooring attachment method question..

tek-Brunswick, Ohio

>If the flooring is 3/4" solid oak, use a flooring nailer. It pulls up the joints nice and tight. They make pneumatic models, but the old fashioned ones that you hit with a BFH seem to draw the boards together better. Remember to leave space between the walls and the flooring. Hardwood flooring expands and contracts with the weather. The base board and shoe mold should cover the space.

Re: Shop oak flooring attachment method question...

#6

PS

tek-Brunswick, Ohio

>Most tool rental stores have flooring nailers. Home Depot also sells them.

Re: Shop oak flooring attachment method question...

#7

Ellis Walentine

I vote for glue

Ellis Walentine

>I've laid floors both ways, with and without mastic, and I feel that the mastic is worth the mess and hassle, if for no other reason than it keeps the floor from squeaking. I know it's not the galoot way, but it works for me. Decent flooring mastic has enough flexibility to handle normal expansion and contraction of the oak. Be sure to leave enough of a buffer zone at the edges of the room to absorb aggregated expansion. If the wood is fairly dry to begin with, I suggest using spacers between courses. I used to make them by cutting 2" long sections off of steel pallet banding. Place them a couple feet apart in the seam when nailing that course. Spacing your planks this way can save you a world of woe during the summer, when the wood absorbs moisture and expands by 5% of its width.

Ellis Walentine, Host

Re: Shop oak flooring attachment method question...

#8

Re: Shop oak flooring attachment method question.. *LINK*

John in Kerrville

>You can also check out the National Hardwood Manufacturer website. They give some pretty good info that might make it easier.

https://www.nofma.org/Portals/0/Publications/NOFMA%20Installing%20Hardwood%20Floors.pdf

IF you have cable or other high speed internet connection, I suggest downloading their manual (link above).

john


Installation manual

Re: Shop oak flooring attachment method question...

#9

Don't glue, let it move with the seasons!

Alan DuBoff

>John,

I wouldn't glue at all, if anything I would want the floor to be able to move with climate changes.

I installed a solid wood floor in my shed I built a couple years ago, and just used a Bostich stapler I borrowed from a friend. Worked much better than a nailer, IMO. I used pre-finished floor, so it went in quick and looked good that day.

Although the wood floors don't float, they do move with seasons and you should leave space around the outer perimeter for movement as well. I think I left about 1/2" - 3/4", if memory serves correctly.

Re: Shop oak flooring attachment method question...

#10

Re: Debunking "flooring movement"

Dave Mount

>Apologies to those that have seen this before, but it is germane to this discussion. I posted a version of this on the noisy side a while back, but I'll repost an edit of it here, because this thread keeps referencing the need to leave gaps at the edges of wood floors.

Before I get into the expansion thing, I wanted to comment on gluing flooring to the subfloor with a suitable adhesive. This does not stop a floor from moving and it is not the intent. The idea is to use a semi-flexible mastic (as Ellis suggested) that will help fill voids and prevent squeaks without creating stress from restrained movement. It is used in wider plank sizes because the wider the strip, the greater the spaces between the fasteners (which are only on the tongue side). So gluing down a floor with a flexible adhesive is not really the opposite of "letting it move."

Back to the "gap for expansion" thing. I find this an interesting piece of "conventional wisdom", because as I'll argue, the superficial explanation of it defies common sense. The fact is that wood floors don't (under normal circumstances) don't move as a unit -- the expansion is taken up by compression at each individual joint, not at the edges. Think about it; if the floor expanded 3/4" at the edges during the summer (and the expansion would be way more than that if it was a 15' wide board), it would pull the nails at the edges and it would never go back the following winter. Also, you couldn't ever install a floor with a border, because the border would be pushed apart when the floor moved. A direct observation is that (unfortunately) I'm still missing a few pieces of baseboard in the house and the gap at the edge of the floor doesn't change dimension seasonally, it's the same today as it was when I laid it (OK, I don't have a caliper on it, but no perceptible movement). Another example is at the door thresholds where I laid the flooring to within 1/8" of the threshold and caulked the gap -- nothing has ever moved, the whole thing is stable. If the floor was moving substantially at the edges, the caulking and/or the door threshold would have been pushed out.

Movement being taken up at the joints between individual boards is also why you don't glue the edges of solid wood flooring -- it would panelize the floor and it would start to move like one huge board.

So why does everyone say "leave a 1/2" for expansion"? Good question. Here's my belief of why it may be important. As I've explained, it is not needed under ordinary circumstances. But, it may be needed under extraordinary circumstances, i.e., catastrophic wetting of the floor. The power of expanding wood is incredible, and the amount a floor would expand if it were actually wetted to the fiber saturation point is way more than what would occur under normal seasonal cycles. Using figures from Hoadley's book, I calculate that a flatsawn red oak floor 15' wide would expand by over 12" going from 7% MC to 30% MC. An 80' wide hard maple floor (like gym or ballroom) would expand over 6 feet! I've seen pictures of things like gym floors that got flooded, and it's amazing to see the floor pulled up out of the subfloor and sitting there in "standing waves" as it curls in a sine wave to take up all the expanded width.

So how does this relate to flooring in a house? My thought is that a gap at the edge (and only along the long grain edge, obviously) is there so a catastrophically expanding floor doesn't push the walls out. Sounds crazy, but think about it. If there's a gap, then by the time the flooring edge reaches the sill plate, the nails holding it to the subfloor will be largely pulled from the subfloor -- not completely maybe, but largely. Being freed from the subfloor allows the pressure from the expanding floor to be taken up vertically by buckling. If the floor were still firmly attached to the subfloor, the pressure would be applied more directly outward to the sill plate. The same would be generally true for glued floors -- the flooring to subfloor bond would have to be broken before the flooring reached the sill plates.

I'll caveat all this by saying that it is the only explanation I've ever come up with to explain something that is otherwise nonsensical. I've never had this theory affirmed by anyone with any authoritative knowledge; but then again, I've never had it countered by anyone with any authoritative knowledge. I actually wrote to Fine Homebuilding and presented this argument after they had an article on flooring that had the "1/2" for expansion" bit in it, but they didn't respond. As above I argued above, just the existence of floors with borders completely debunks the idea that the floor is moving perceptibly as a unit under normal circumstances. So if not that, why?

Another possible explanation is that gaps were originally left simply because there was no need to fit it tightly when it would be covered by baseboards and the expansion thing just grew up on its own. However, I hate to invoke an argument that the whole thing is a myth if there could be a rational explanation related to expansion.

Best,

Dave

Re: Shop oak flooring attachment method question...

#11

Slight thread hijack

Bill Schoenbeck

>Apologies to all for the thread hijack.

To tek in Brunswick, Ohio. Hello. I just noticed your location and had to inquire how are things in Brunswick these days? I grew up there from the mid 50's until leaving in 1971 to join the Navy after high school. I have only been back once in 1983 and did a drive through to show my better half where I grew up. The place had changed quite a bit of course. I lived on Hudak Dr and the farm that used to abut our back yard had long since turned into housing.

I've lived in San Diego CA ever since 1977. All my family moved to Florida so with the exception of a couple cousins still in Cleveland area there was no reason to go back for a visit. I was just surprised to see reference to my home town on a site I lurk at frequently. Made me think of the good old days.

Best Regards,

Bill

Re: Shop oak flooring attachment method question...

#12

I think there is a couple reasons...

Alan DuBoff

>I do think there are reasons for leaving the expansion gap, and the floor while not moving as a whole does move as it acclimates.

When I laid the floor in my shed, it was apparent that some pieces required force to get in place, either a tight tongue, or a slightly snug fit that required some hammerin' to get in place, etc...

Also, a floor is not like building a cabinet, and if you spent the time getting the floor fitting perfect, it would require much more time to cut, IMO. All of our mileage varies in that regard.

I can see using mastic that is soft enough to allow movement, but to me it seems un-needed. I haven't noticed the wood floors squeaking yet, but maybe they will with time.

Re: Shop oak flooring attachment method question...

#13

Re: ease vs. expansion

Dave Mount

>I don't disagree a bit that leaving a gap at the edges speeds installation. My point is that the CW is that you leave that gap "for expansion", and that really doesn't make any sense, except for the possible exception of the scenario I outlined.

Squeaks are the bane of floor installers -- it's a certain call back, and they're a heck of a lot easier to prevent than fix. I think that's why there's a lot of concern about it.

Best,

Dave