Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Tool cabinet progress!

Posts

Tool cabinet progress!

#1

Tool cabinet progress!

Dominic Greco in Richboro PA

>Hi everyone,

I finally installed the patches to fix the miscut dados and then re-cut them this past weekend. I also made several holders for my saws and spokeshaves. I installed them temporarily above my work bench so I could see how well they functioned.

The backsaw holder is a simple idea I picked up from "The Toolbox Book". It's rather simple to use and holds the saw very securely. Since the saws will be stored on the inside of the doors, I needed a solution that was low profile. The Dozuki and Gents Saw holders are just blocks of wood with a saw kerf.


The spoke shave holder is made from hardboard. But the final design will be cut from hardwood. From this mock up I found I can reduce the space between the tools as well as make the holder not as "deep" (wide). I believe it sticks out too much. BTW, if anyone has a better solution to hanging their spoke shaves, please feel free to show them off! :>)


I also managed to FINALLY get all the carcass parts together for a dry fit. I was really very happy with the way all the joints fit. The next step will be the glue up, then cutting and installing spines at the mitered corners.


Thanks for looking.

See ya around,

Dominic

Re: Tool cabinet progress!

#2

Re: Tool cabinet progress!

Stephen Shepherd in the State of Deseret

>Dom,

Nice recovery on the dados, I couldn't see the repair. Are you sure it is big enough? My tool cabinet proved too small, I am remodeling the interior now for better tool storage.

On the spokeshaves you might try short Shaker pegs or drawer knobs to hold your spokeshaves. Do they have holes for hanging? Another method for storing them is up and down (verticle) in a block with holes large enough for the handles.

Stephen

Re: Tool cabinet progress!

#3

Short Shaker pegs!

Dominic Greco in Richboro PA

>Stephen,

Short SHAKER pegs!!! BING BING BING!

That is a FANTASTIC idea! Those are just the thing I was looking for. The will fit perectly into the space I've set aide for my spoke shaves. And it's something I can use my lathe for. It's been acting might sullen since I began on this project (I think it's getting jealous).

And as far as capacity goes,....well lets just say that if I tried to make it fit everything I might as well build a tool SHED rather than a cabinet! :>)

Seriously, it's designed to hold 35 bench planes and numerous other tools. It's also designed so I can switch the internal configuration from 1/2 shelves and 1/2 hanging planes to all shelves or all hanging planes. And with the things I learned from this project, building an additional one will be a piece of cake! (I say that NOW)

See ya around,

Dominic

Re: Tool cabinet progress!

#4

Re: Tool cabinet progress!

Michael Rogen

>Dom,

I've just picked up on this thread and since it is something that I need to do, I was wondering what your inspiration or basis of your design was. So far it looks great, so any help would be greatly appreciated.

Thanks aand take are,

Michael Rogen

Re: Tool cabinet progress!

#5

Lots of places

Dominic Greco in Richboro PA

>Michael,

wrote:

"...I was wondering what your inspiration or basis of your design was"

I started the research for this project back some time in September of 2007. Lots of places provided me with the information for the design of this tool cabinet. While the basic design is mine, some design information came from a wall hung tool cabinet article recently featured in FWW.

In addition, I asked questions here and on other WWing sites and made notes of the replies. When pictures were provided I saved them and used what I could for reference. After I had gathered enough preliminary information for a layout, I drew up the basic design in AutoCad and then laid in scale models of my hand planes. After that it was just a matter of seeing how everything fit.

See ya around,

Dominic

Re: Tool cabinet progress!

#6

Re: Lots of places

Michael Rogen

>Dom,

Thanks for the quick response. This information will be helpfull.

Take care,

Michael

Re: Tool cabinet progress!

#7

Yes, progress at last!

Scott Burr in Ben Lomond CA

>I've been wondering what's been going on with your cabinet after you posted your "redesign" (that's a nice way of saying screw up). It looking very nice!

Glad to see your loosing the masonite...