Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Snowshoe bending How It's Made

Posts

Snowshoe bending How It's Made

#1

Snowshoe bending How It's Made

ThomD

>How It's Made had a short tonight on how to make snowshoes. The first step, once the stock was 4S was to install a metal strap with brackets at each end that supported the toe during bending. This compresion strap was necesarry because, among other tings, the stock was probably sawn cross grain. The stock and strap went into a full length steamer, and after 30 minutes a piece was withdrawn and wrapped around a metal form. This was a fully round shape, so the tail end was scarphed and overlapped. Once the basic shape was bent and a spacer inserted the toe was inserted into a brake and the toe deflection was pressed in. This was done without any apparent additional steaming.

I should note that during the initial profilling of the strip, the toe had been reduced in size for easier bending. The one point of interest was that when the support strap was removed from the toe, there was a lot of grain that had lifted on the outside due to grain run-out. This was agressively ground down, so that the overall thickness was probably in the traditional range of 3/8". The machinery didn't finish things up with a thicker toe, but it made it possible to use less optimal wood. Not to say modern wooden shoes aren't durable, but when I first saw the reduced section in the traditional shoe it looked pretty thin. In comparison it seems more than enough now.

Re: Snowshoe bending How It's Made

#2

Re: straps and bending

Dave Mount

>That's interesting. Although I've bent a number of things, I've never used straps. From what I had seen from various sources, I thought the straps had to do with applying the bending force evenly. Some sources I'd read talked about it "supporting" the wood which I took to mean something like how a tight mouth allows a plane sole to support fibers and prevent tear out.

However, the recent pointer someone gave to Lee Valley's steambending pamphlet explained it in a whole new way that made it all make sense. In that booklet, they explained that steam bending involves mostly compaction of fibers, that even steamed wood doesn't stretch to speak of and will break if put in too much tension (failure on the outside of the bend). Apparently the role of the metal strap is to keep the outside dimension relatively fixed and apply all of the force as compression on the inside of the bend, where the wood is compliant. Made perfect sense.

I still haven't done the bending for the snowshoes I have in process, but in that technique you thin the 13/16" square blank to 5/16" thick at the toe, and you remove the wood from the inside of the curve (naturally) so the grain is continuous around the outside of the bend.

In preparing my blanks, we used only riving to break down the blanks. This created a lot of waste because a split was difficult to control for the entire length of a 12' log and if the split ran out anywhere along that length, the blank was ruined. While it was an interesting experience, I think a very viable compromise between pure riving and working from processed lumber would be to quartersaw the green log on a sawmill, leaving the live edge on the bark side. Then you could rip out rough blanks by ripping paralell to the bark and have continuous grain in your blank, but yield many more blanks.

Best,

Dave

Re: Snowshoe bending How It's Made

#3

Re: Snowshoe bending How It's Made

Paul Kierstead

>I love that show. That episode is sitting on my PVR at home (I just checked), I look forward to watching it! They have quite a few WW episodes here and there, typically something unconventional as we think of WW, like the episode on boomerangs.

Re: Snowshoe bending How It's Made

#4

How It's Made, One of my favs!

Scott Burr in Ben Lomond CA

>I saw this one a few weeks back. I wish they would have spent more time on the making of them. Especally the knotting.

Re: Snowshoe bending How It's Made

#5

Re: How It's Made, One of my favs!

ThomD

>Then you would never know how to do it fast. She was really getting 'er done. Part of it was that her rawhide really was raw and wet and slimy.

Re: Snowshoe bending How It's Made

#6

Re: straps and bending

ThomD

>I've used the straps a lot, even masking tape on guitar perfling has stopped a blow-out for me. What surprised in this case was that it didn't really seem to work (at least on the one thy chose to show). The brackets flashed by so I didn't really see them going on. But basically the strap had two two tabs at the end that were wrapped around the stick. I'm guessing these just weren't well enough on to stop the strap from shifting, so the grain blew out. That's how the tape works on the thin pieces it could break or come off, but so long as it doesn't you the outside layer won't lengthen.

I'm sure you are right about sawing. My problem would be getting the 12 foot piece split into quarters. It's real hard to break out when it is in a shorter log. One would need amazing wood. They must have managed for canoes in the old days. I'd like to see that.