Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Chisels for making molding planes

Posts

Chisels for making molding planes

#1

Chisels for making molding planes

Dave Mount

>Well, last Friday I finally broke down and bought a (wood) lathe. I just got tired of trying all kinds of workarounds to make round tool handles. I also got tired of drueling over all the nice handles I see posted here (you know who you are. . .).

The first project was some handles for two chisels I made from O-1 tool steel, pictured below. The upper chisel is a 1/10" chisel which I ground down from a 1/8" O-1 blank (you are looking at is from the side, obviously). This chisel is intended for reaching up through the mouth of molding planes to remove the waste after the bed and breast lines are cut. It looks kind of like a mortise chisel, but it's for paring; I made it "deep" to give it some rigidity (1/10" is pretty narrow), but it's ground at a little under 25 degrees.

The lower chisel pictured is a 3/4" wide bevel edge chisel. What's different about this is that it is only 1/8" thick, which allows you to pare down the bed of the plane from the escapement side (assuming the escapement is sized for a 1/8" thick iron).

The mallet is just hanging around contributing nothing. You can tell a lathe newbie because he's running around the shop trying to think of anything round he can make. It's hard maple, and I see the camera was kind enough to highlight some places where my sanding did not cover my poor turning technique.

I hardened the chisels by heating them in my forge -- I wanted to get the bulk of the blade heat treated and I didn't think I could get enough of it hot in the shop using torches. They were tempered in the kitchen oven at 400 F, which should bring them in circa 62 Rockwell. Pic following tempering follows.

The handles are turned from a piece of Australian lacewood that I picked up when I was in Australia (east coast) a few years ago. I went to a lumber dealer to see the woods for sale (strange to see the "imports" of cherry and walnut. . .) and was looking for a little something I could stick in my luggage. There was a piece of blocking laying in the warehouse roughly 2" x 4" x 3' that was clear QS lacewood. I asked if I could buy it and the guy just laughed and said "take it." Part of it I resawed into 1/4" pieces and made door panels for a bath cabinet. The rest has been laying around the shop looking for a purpose -- this seemed as good as any.

The brass ferrules started life as flare nuts that I ground the hex flats off of and polished.

Expect to see more tools soon -- I'm on a newbie high.

Best,

Dave


img

Re: Chisels for making molding planes

#2

Re: chisel blades after tempering

Dave Mount

>The oxidation colors didn't photograph very well -- they come across as almost brown, but in real life they were more toward a medium straw. The dark blotches are just oil crust I didn't bother to polish off before tempering. The rainbow on the tang is left over from the hardening step, the tangs were sticking out of the fire in the forge. However, the blades were at critical temperature over their full length.

Best,

Dave


img

Re: Chisels for making molding planes

#3

Yowza, eye candy!

Alan DuBoff

>Great work, they look wonderful!

Re: Chisels for making molding planes

#4

Re: Chisels for making molding planes

Derek Cohen (in Perth, Australia)

>Mmmmm mmmmmm!

Dave, my first thought was that you have been lying about your turning life, then it was that these looked like Blue Spruce's influence (a compliment!), and then 'what is that She-oak doing there?'

Regards from Perth

Derek

Re: Chisels for making molding planes

#5

Re: Blue Spruce influence - guilty as charged

Dave Mount

>Hi Derek--

You are absolutely right about me stealing the shape near the ferrule from BS chisels. I changed the shape some on the other end. I kind of like chisels that have a somewhat bulbous end that nestles in the palm. Least that was the idea -- we'll see how I feel after they see some use.

Thanks for the kind words,

Dave

P.S. I take it She-oak is the same as what gets marketed in the U.S. as "Australian lacewood"? I've often wondered that looking at things you've made from She-oak.

Re: Chisels for making molding planes

#6

Oh no Dave...

Scott Burr in Ben Lomond CA

>Kiss us and flat work goodbye. We'll see you later, it was nice knowning you.

Maybe I'll come visit you on the turning board sometime. 8^)

What lathe did you get?

Re: Chisels for making molding planes

#7

Re: Not likely. . .

Dave Mount

>Hey Scott--

I'm not ready to give up flatwork, but I do get a kick out of making my own tools.

I went entry level on the lathe, the Delta midi. I had been thinking I would save my shekels for a full size lathe, but decided right now a lot of what I want to make is small, and I'd rather make it now than later. Not a high end lathe by any means, but it's fine for a newbie turner and smaller projects.

There was a "what lathe should I buy" thread on the turning board recently and all the suggestions were $1-$2K lathes. I have no doubt that those are high quality lathes, but I felt kind of sorry for the guy that asked, I'm not sure that was the answer he wanted.

Marking knives are next on the list. . .

Dave