Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Degrees of Separation

Posts

Degrees of Separation

#1

Degrees of Separation

David Miller from Iowa

>Sorry about the topic, but you folks are my "go to" people and I don't hang around on any other boards. I need a 2 pin spanner wrench with pins 1 3/8" apart. Google has failed me. Any help?

Let's see, to make it legitimate, it is for my angle grinder, to change to a wire brush, which will clean my anvil, which I will use to forge a chisel, which I will use for woodworking. Hah - try that Kevin Bacon!

thanks

Re: Degrees of Separation

#2

What's the make of the grinder?

Wiley Horne -- So. Calif.

>I checked my Makita wrench, David. It's 13/16".

Wiley

Re: Degrees of Separation

#3

P.S.

Wiley Horne -- So. Calif.

>It occurs to me that if you can find two pins the right size--cutoff nails or something--you could get a pair of channel locks across them, or just a straight piece of steel like a screwdriver shank between them, and get that nut off and then back on again.

Wiley

Re: Degrees of Separation

#4

Re: Degrees of Separation

Moses Yoder in White Pigeon, MI

>You could take a piece of flat steel and two steel rods and make your own pretty easily. If it is a dewalt angle grinder I probably have the wrench but am eventually probably going to need it myself.

Re: Degrees of Separation

#5

Re: P.S.Spanner

Stephen Shepherd in the State of Deseret

>A pair of nail sets in a vice will work as a variable spanner wrench.

Stephen

Re: Degrees of Separation

#6

adjustable spanners

Bill Houghton, Sebastopol, CA

>I don't know how easy these are to find in the retail market - mine was from the garage sale market - but there are adjustable pin spanners. Basically, two legs pivoted at one end, like dividers, with pins at the end. The question then is whether the pins fit the holes.

Call a bearing and hydraulic shop or a tool repair shop or both - you should be able to get direction from one of them.

Re: Degrees of Separation

#7

Re: Degrees of Separation

wilbur

>McMaster-Carr sells an adjustable spanner wrench for less than $20.

Re: Degrees of Separation

#8

Flag down a Snap-on truck

Bob Hackett

>That way you can see if it fits before you buy.Garanteed for life too!

MB

Re: Degrees of Separation

#9

Try a bycycle shop,

Paul in NJ

>they use pin spanners on several parts of the bycycles.

Paul Dzioba

Re: Degrees of Separation

#10

What I use,

Andrew F in Australia

>When I've lost the spanner, is a piece of wood about 50mm across, and I just screw in two 8 or 10 gauge screws (whatever's the required pin diameter) at the right separation then cut off their heads.

Paint the wood bright orange or similar so you can find it and so you don't throw it out.

Not only an instant grinder spanner, but an easily replaced one if you lose it as well.

Cheers,

Andrew

Re: Degrees of Separation

#11

Re: McMaster-Carr  *LINK*

Bob Entwisle in NJ

>


http://www.mcmaster.com/ctlg/DisplCtlgPage.aspx?ReqTyp=CATALOG&CtlgPgNbr=2714&CtlgEdition=114&sesnextrep=369143495974946&ScreenWidth=1400&McMMainWidth=914

Re: Degrees of Separation

#12

This is where I'd go too.

Scott Burr in Ben Lomond, CA

>