Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

Lost ball in high weeds

Posts

Lost ball in high weeds

#1

Lost ball in high weeds

Wiley Horne -- So. Calif.

>Knowledgeable ones,

What brand and type of veneer tape do I need for jointing sawn veneers? Veneers are kinda thick (3/32"), and maybe a slight wave to them in places.

It will take 4 veneers to make the pattern I am trying to make, each one approx. 8" x 16". Total joined size approx. 15" x 31" after trimming. My thought is first, to edge-join the pieces using veneer tape and hot hide glue, and then glue the full 15 x 30 sheet down onto the substrate using Old Brown Glue, holding it down with cauls acting on a sheet of plywood to spread the load evenly.

All suggestions appreciated!

Wiley

Re: Lost ball in high weeds

#2

Re: Lost ball in high weeds

Stephen Shepherd in the State of Deseret

>Wiley,

Can't help you with your lost ball but in the seventeenth century wacking the ground with a stick and cursing was called Witchcraft today it is called golf.

I don't know the brand but I like the kind with the cute little holes. I have used both kinds and the perforated one allows you to see your joints while you are working on them. There is also less paper to remove when you are done.

Stephen

Re: Lost ball in high weeds

#3

Re: Lost ball in high weeds

Bill Leffingwell Richwood wv

>A 2nd vote for the tape with the little holes(don't know the brand either)I don't do a lot of veneering,but this has been trouble free it sticks and wetting it first makes it easy to remove.

Bill

Re: Lost ball in high weeds

#4

Ellis Walentine

My two cents

Ellis Walentine

>This is a case where, as you say, Wiley, you want glue in the seams because of the thickness of the veneer (1/10"?). Regular veneer tape will probably hold the joints together, but it won't pull them together. I think I would use masking tape for its stretching/clamping action. I don't use it on thin veneers, especially softer woods, because its thickness tends to crush the surface fibers under pressure from your press. (Of course, I used to use a huge old screw press that could deform oak. :-) Here, I would tape all your pieces together first, with as much stretching pressure as you can get. Then fold the leaves open, brush some glue in the seams, close them up and immediately glue the whole shebang to your substrate. Don't forget to balance the construction with backing veneer. I also think I would use the old brown glue for everything. Hot glue might gel a bit and force your gluelines apart if you don't get them closed up in time.

Ellis

Re: Lost ball in high weeds

#5

Re: Lost ball in high weeds

Wiley Horne -- So. Calif.

>Thanks very much! Funny thing, sometimes you start looking into a new area, and feel like you're getting up the (theoretical) learning curve pretty fast. But this veneering thing, I started out with some initial good advice (thanks Tom), but then the further I looked into it, the dumber I began to understand that I really am.

I will use the holy tape, and will have to make an experiment about edgejoining with hot glue vs. Old Brown Glue, per Ellis' suggestion.

Prolly take a few screwups on scrap to get something workable. Looking for seamless joins is the main concern I have right now.

Thanks again,

Wiley

Re: Lost ball in high weeds

#7

Re: Lost ball in high weeds

Steve Hamlin

>As this is pretty much guitar back thickness, suggest joining by tenting between two rows of nails set just a smidge tight of the total width (won't need much sideways clamping pressure assuming the pieces are well jointed - candle the joints to be sure.) Run packing tape (plastic stuff) under where the seams will be, lay the outer two against the nails, with the middle two tented up, run three beads of hot hide, snap down flat then weight or clamp down the seams and wait.

If any of the seams are out of alignment, use a hot iron with a damp cloth to press them flat and reclamp.

If you're using cold glue for the veneering, can't see this affecting the HHG seams (though I haven't done this)

As further evidence that I haven't done the veneering - is relative movement an issue? Could be worth making sure the veneer is at least as dry as the substrate (bake it perhaps?)

Cheers

Steve

Re: Lost ball in high weeds

#8

This is very helpful!

Wiley Horne -- So. Calif.

>Steve,

Thank you very much. I think your way is the way to go. This method of 'tenting' between rows of nails overcomes my biggest worry, which is that the seam will find a way to separate just a little during clamping--enough to make a black line. I understand that veneer tape tends to pull the opposing pieces together as it dries, but belt and suspenders seems best.

There _is_ a wood movement issue between the crotch veneer and the substrate. Will either minimize it using quartersawn stock for the substrate, or eliminate it with Baltic birch or marine ply.

Thank you very much! Wiley