Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

Hammer head attachment

Posts

Hammer head attachment

#1

Hammer head attachment

Skip in Falls Church

>I have either an older shoemaker's hammerhead or a copy of one and need to know how this type of hammer head was attached to the handle. The opening for the handle is not the standard "adze eye" opening of modern hammers but rather a truncated cone about 5/8" diameter at the bottom (where the handle goes in) and 1/2" diameter at the top where you'd normally put a wedge.

Since the opening at the top is smaller than the opening at the bottom, it seems to me that putting a simple wedge in would not really secure the head to the handle. I know that attaching hammerheads to their handles took several different forms before the adoption of the modern adze eye but never paid any attention to what they were aside from strap heads.

Did they wedge this type of head? Or is there some other way to attach it?

Thanks,

Skip

Re: Hammer head attachment

#2

Re: Hammer head attachment

Todd Hughes

>Haven't really paid that much attention to hammers but most older hand forged axes and hatchets had eyes that were bigger on the bottom then on the top, I have some old ones that the eye is just a sliver at the top. If you think about it not a very good way to make them but that was how they were made, matter of fact one of the things i look for to see if the head is really old.. I used to forge out axe heads and I think they were made this way because when you drifted the eye out to shape it is much easier to do it from the bottom then the top because you don't have to worry about deforming the axes ears...well my guess.

...Imagine your hammer's head was held in by using a wedge. I always liked to use a wooden wedge and then if it loosened overtime go with a metal wedge to re tighten it. A little squirt of this stuff called Chair lock will expand the wood and keep it from drying out and shrinking too....Todd

Re: Hammer head attachment

#3

What about a metal strip?

Alan DuBoff

>Todd,

Curious, I've seen some smithy tools that had heads which were attached with a strap over the top, through the center of the eye. Hammers, punches, etc...would those have been used in the old days on a hammer?

Scott Thomas has many of his tools like that, and I think it is because it is easier/faster to make the handles, and since it's only a handle in some cases to hold the tool while the smith strikes, it is not being used like a hammer and doesn't have the stress on the handle. I think Scott puts them through the eye and over the top, with a screw below the head locking the handle on. There sure was some crude tools forged...I've done some fine turdlettes myself...*lol*

Re: Hammer head attachment

#4

Re: What about a metal strip?

Moses Yoder in White Pigeon, MI

>I think most of the straps over the top were made earlier than the standard wedged in handle, and probably as Todd mentions because of the hole being smaller at the top. Amazing how some of the simplest things are just not seen until suddenly someone sees it and then you pound your forhead and say "Why didn't I think of that!" I used an axe yesterday that didn't have the head on really tight and it wastes a considerable amount of energy. I like attaching a handle to the head with a wood wedge front to back and a steel wedge pounded in across.

Re: Hammer head attachment

#5

Re: Hammer head attachment

Stephen Shepherd in the State of Deseret

>Skip,

Cobbler's hammers are not going to get a lot of heavy use, it doesn't take much to drive those little wooden pegs. Most of the time the hammer is used for flattening stitching and used more like a veneer hammer than a cabinet hammer.

With old drifted eyes, fitting a handle can be a problem, I use soot on the inside of the eye to mark the handle to get a tight fit, then I use hide glue and glue the heads on as well as the customary wedge.

I guess we could get into a discussion as to which way to orient the wedge, with the eye or cross the eye?

Some old handled tools have perfectly parallel walls on the eye and those tools are easier to handle up. I have seen some that are bigger on the bottom, narrow in the middle and wider at the bottom of the eye, I presume they drifted from both sides.

As for strap hammers those are constructed specifically to accomidate the strap. Some straps are removable and the handle can be shaped to fit, then the strap re-installed and the handle fixed to the strap. Other straps are attached to the head and can be a bit tricky to fit up, especially if the straps are inlet into the handle.

Like Todd said those eyes are a dead giveaway of an old tool.

Stephen

Re: Hammer head attachment

#6

Re: Hammer head attachment

Marv....... Northern California Lake Co.

>Hi Skip,

Actually, that type of hammer head makes more sense than other heads with eyes that taper the other way. It's much easier to fit a handle, just taper the handle to fit and bang it in. The smart thing about it is, the handle should extend out the top a bit. A wedge can still be hammered in to expand the wood, but with the wood extending, it will be very tight at the small end of the eye and will be force over the top of the metal. When the handle becomes loose, just give it a whack then drive the wedge in farther. When it extends beyond the top, just cut it off so you still have about 1/4" extending.

Marv

Re: Hammer head attachment

#7

The one thing I think about though...

Alan DuBoff

>Is that hammers had existed much longer before, most likely, and they certainly knew how to and understood how to handle hammer heads, so it seems odd that there would be an eye that was smaller on top. Must be some reason...although I don't know what...;-)

Re: Hammer head attachment

#8

Re: The one thing I think about though...

ThomD

>Well it would make sense for a turner's ahmmer since he could just dash off a replacement. I have several cabinet hammers I made handles for early on, and either aren't all that perfect, or maybe the cherry is too soft. Either way they regularly loosen every so often, and then I just hold them by the end of the handle, head dangling, and give them a few more wack with another hammer on the end of the handle. The head will work it's way up the handle often peeling back some wood. So it isn't all that tough to reseat them with a few taps. And if that is the way you are proceeding then why not a tapered stick in a tapered head? Like a socketed chisel handle, except of course one removes those by tapping from the side.

One thing about iron heads is that they can be split by too vigourous wedging.

Re: Hammer head attachment

#9

Re: The one thing I think about though... *LINK*

Skip in Falls Church

>Hi Alan,

I knew the so called adze eye hammer head was of fairly recent vintage. I was pretty sure it had been invented in the mid 1800's and I found this reference:

In 1840, a blacksmith in the United States named David Maydole introduced a claw hammer with the head tapering downwards around the opening for the handle. This provided additional bearing surface for the handle and prevented it from being wrenched loose when the hammer was used to pull nails. His hammer became so popular that his blacksmith shop grew into a factory to keep up with the demand. Most claw hammers made today use this same design.

It's hard to believe that in the history of hand tools that such a simple concept came so relatively late. It's just that I'd never encounted anything else. Encountering something new, I decided to ask. :)

Skip


http://www.madehow.com/Volume-4/Hammer.html

Re: Hammer head attachment

#10

Re: Hammer head attachment

Skip in Falls Church

>Hi Todd,

Thanks, seems like the best way to approach the problem - along with the other suggestion of just tapping it down tighter then redriving the wedge.

Skip

Re: Hammer head attachment

#11

Re: Hammer head attachment

Skip in Falls Church

>Hi Stephen,

I actually got to watch a shoemaker at Williamburg use one. He was, however, insulted at being called a cobbler and the hammer a cobbler's hammer. (Well, at least his Williamsburg persona was.) Of course I didn't take the opportunity to see how the head was attached to the handle because I didn't have this hammer head at the time.

I also asked about the "claw" and he demonstrated using it to smooth the edge of the sole like a slicker.

I'm not sure of the age of this hammer head. Both the hole and the "claw" are indicative of it being older as the "claw" is fairly straight. It seems that more modern ones tend to have that curve exagerated. However, there is what appears to be the remains of a casting line between the head and body on one side although I don't see any other traces anywhere else.

The hammer part was in pretty bad shape with a huge pit (about the size of a penny) and took a lot of work to get smooth, slightly dished and polished up.

Skip

Re: Hammer head attachment

#12

Re: Hammer head attachment

Skip in Falls Church

>Hi Marv,

Thanks for the suggestion of leaving a bit of the handle above the head. That makes a lot os sense!

Skip

Re: Hammer head attachment

#13

Re: Hammer head attachment

Stephen Shepherd in the State of Deseret

>The casting line between the body and the face is probably the weld line of the steel face forge welded to the iron body. Sometimes the pane has a laid steel face as well.

I should have said shoe maker's hammer or shoe hammer, as a cobbler just repairs shoes. Most old catalogues that illustrate the heads do not illustrate the handles.

Stephen

Re: Hammer head attachment

#14

How to Tighten handles

Todd Hughes

>The best way to tighten a loose handle isn't to pound on it with another hammer but rather to just tap the bottom of the handle on somthing hard while holding it straight up and down. This will drive the head down tight. When I was blacksmithing this became sort of a habit befor forging and always kept my heads tight.

... I always liked to wedge an eye with a wooden wedge that went corner to corner in the eye. This way it applied pressure to the front of the eye as well as the sides and holds better. I have heard you should use a soft wood for the wedge. I tried alot of pine wedges but then went to using Hickory and dam if i could ever tell the difference. I used to use the pieces of hickory I split off of the side of the handle when fitting it into the eye for wedges so was easier to use hickory for the wedges.....Todd

Re: Hammer head attachment

#15

Hammers are almost old as dirt...

Alan DuBoff

>Skip,

That dates surprise me, I knew hammers were old, but geez...those dates make my head spin. They don't say too much about the eye though.

From the doc:

"If the hammer has a steel or graphite fiber-reinforced core, the handle is inserted up through the adze eye of the head. Liquid epoxy resin is then poured through the top of the hole to bond the handle in place."

And there you have it, in the days of olde they would reach for some epoxy and be done with it...:-/

Re: Hammer head attachment

#16

I do mine kinda similar...

Alan DuBoff

>Todd,

I do my smithy hammers kinda similar, but I have been cutting a slit in the portion of the handle going in the eye, from front to back, and I put a wood wedge (which I have also cut from old hickory handles), and then drive a metal wedge in diagonally.

I haven't done all my hammers, but have done the ones I use and which have had the heads come loose. I don't have a lot of hammers, but have a few commons ones...my favorite is just an old cast rounding hammer, which was commonly used by farriers. I was taught with a rounding hammer. I also use a bell peen which is a farrier's type peen, with a modern style bell shaped head and a ball peen on the other end.

I have wanted to make some of my own hammers, and Phil Koontz sent me some axle pieces from Alaska, I just haven't done it yet as I don't have any tongs large enough to hold them. I need to make a punch also, I don't have one for a hammer head. :-/

Re: Hammer head attachment

#17

Re: Hammers are almost old as dirt...

Skip in Falls Church

>Hi Alan,

I think I first saw the 1840 date on a History Channel program and it surprised me. It seems so obvious now it makes you wonder why it took them so long to figure it out.

Skip

Re: Hammer head attachment

#18

Re: The one thing I think about though...

Todd Hughes

>"I knew the so called adze eye hammer head was of fairly recent vintage. I was pretty sure it had been invented in the mid 1800's ....It's hard to believe that in the history of hand tools that such a simple concept came so relatively late."

Try forging one out by hand and it won't be much of a surprise as to why Hammers weren't made that way befor.....Todd

Re: Hammer head attachment

#19

Re: Hammer head attachment

Stephen Shepherd in the State of Deseret

>Here is one I found in Salaman's Dictionary of Leather-Working Tools. The handle is turned and the straps form around it and hold the head. I have seen some that the straps are held with one or two rivets.

Stephen


img