Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Plough plane question

Posts

Plough plane question

#1

Plough plane question

wilbur

>[I would have said plow plane, except that my plane comes from England.]

I have a Record 044 plough plane that I really tried using for the first time this week. I have a question about the fence and the depth stop.

I'd like to make a groove that is pretty close to the edge of the board. It's close enough to the edge of the board that if I use the fence to mark the distance of the groove to the edge, the depth stop can't be used. If I lower the depth stop, I have to move the fence out of the way to set it at the depth that I want.

What I did was to use the fence to get the groove started, then removed the fence and dropped the depth stop, and proceeded to plow (sorry, plough) the groove to the depth that I wanted, using the sides of the groove to keep the plane in line. The problem I see with this method is that I would need to start all the grooves first, then remove the fence, then plough (got it right that time) the grooves to final depth. If I forget to start a groove, it would take some futzing around to get the fence set back just right.

I think that there must be a better way to do this. How do you deal with this situation?

Re: Plough plane question

#2

Re: Plough plane question *LINK*

Ian in Sydney

>Wilbur

I think you have the fence on the wrong side of the plane.

Looking along the groove in the direction you are planing, the fence should be on the left and the depth stop on the right.

the link should help


Alf's Cornish Workshop

Re: Plough plane question

#3

Re: Plough plane question

Stephen Shepherd in the State of Deseret

>Wilbur,

I am not sure I understand your dilemma, but I think you can make an auxillary fence with a notch for the depth stop. This will allow you to cut closer to the edge with the depth stop in place.

Isn't the Record Plough a bit Occidental for you Wilbur?

Stephen

Re: Plough plane question

#4

Re: Plough plane question

Derek Cohen (in Perth, Australia)

>Wilbur old chap

For the life of me I cannot picture what you are doing! Ian may be right when he says you have it set up backwards! :)

The fence and the depth stop are two separate parts of the plane. They cannot interfere with one another.

Here is a picture of a short fence set up for a groove very close tp the edge.



Here is the depth stop. As you can see it is completely clear of the fence.



Your plan to plough sans fence is not a good one. The fence helps guide the cut vertically as well as horizonatally - you can indeed plough without it, but you will lose a valuable aid to make certain you are ploughing vertically. In fact I add a subfence to increase the stability. This can just be seen above.

Regards from Perth

Derek

Re: Plough plane question

#5

Stupid stupid stupid

wilbur

>The fence is on the wrong side of the plane, as you can see here.

Record plough plane with fence on wrong side

In my defense, when I received the plane (bought it on eBay), it came assembled with the fence on the right side, not on the left. Maybe that's why the person decided to put the plane up for sale. :@)

Stephen, I figured if you could give working with MDF a try, I could certainly make a go at using a western plane. :@)

Actually, I do have a Japanese groove plane, but one of the limitations is due to the design, the groove has to be at least 1/4" from the edge of the board. Also, the groove is set at just over 1/4", so I can't make thinner grooves with this plane. I have made larger grooves with this plane by ploughing them 1/4" at a time. There isn't an adjustable depth stop, but it will stop nicely after cutting a 1/4" deep groove. Here are some pics:

Japanese groove plane

Japanese groove plane

Thanks for the help!

Re: Plough plane question

#6

One other question

wilbur

>My Record 044 felt a little chattery, although overall it worked well. I'm going to do some fine tuning of the blade, but I've noticed that the bottom of the skate is pretty roughly milled. It's certainly not as smooth as the soles of the Bailey planes that I have. Is it worthwhile to smooth this out with a file?

Re: Plough plane question

#7

Re: One other question

Warren in Lancaster, PA

>Wilbur, its hard to know what you mean by chattery, but if the iron is not well supported at the very bottom, and is a little loose, it will chatter (harmonic vibration). So you could check that out. I would refine the bottom of the skate just to reduce friction.

Your wooden plow could be made to plane closer to the edge by attaching a slip of wood to the fence. Or you could easily make an alternate fence piece yourself. Make it so it goes all the way to the iron. If you want to plow a wide groove with this plane, plow a groove at the near edge and one at the far edge and remove the material in the center with chisel and rabbet plane.

Re: Plough plane question

#8

Left handed

VTAndy4

>Hi,

Setting up the fence on the right is good for lefties, but as you've noticed, it doesn't allow the depth stop to be used. I've taken to using the fence on the left and planing like a right-handed person.

-Andy

Re: Plough plane question

#9

Just remember, Andy

Bill Houghton, Sebastopol, CA

>we lefties have to learn how to work left AND right-handed. Come the revolution, we'll be in charge...

I find many planes are right-handed planes; I tell myself it's good for the brain to learn to use my non-dominant hand. I always come back to thinking about my grandfather, who could hammer equally easily with either hand (hammering is one of those incredibly complex actions that we think of as simple).

Re: Plough plane question

#10

Not just lefties...but righties too!

Alan DuBoff

>Bill wrote:

"we lefties have to learn how to work left AND right-handed. Come the revolution, we'll be in charge..."

I personally feel it's good for all woodworkers to be able to work both left and right. You just never know when you might find yourself in a situation where you need to use your weak side for what your strong side will normally do. Rasping for instance, or using a chisel, it's good to be able to switch hit, so to speak. ;-)

Re: Plough plane question

#11

Re:member, Push the plane, do not Pull

Stephen Shepherd in the State of Deseret

>

Re: Plough plane question

#12

Re: dominance and strength

Mike Hamilton

>Some of us are even more confused. My right eye/hand/foot are dominant but my left arm and leg are my go-to limbs for strength. My son turned this into a middle school science project and found dominance and strength on opposite sides about 30% of the time.

Regards,

Mike Hamilton

Plainfield, IN

Re: Plough plane question

#13

I can do all woodworking tasks with either hand...

Stephen Shepherd in the State of Deseret

>except use a hammer or mallet. There is something about that particular process that I can only accomplish with my 'good' hand, my right hand.

I can write and draw with my left hand, carve, plane, saw, drill, turn, chop, shoot, both boards and weapons, eat and gesture with my left hand.

But with hammer or mallet in my left hand anything I intend to hit is safe as I just can't make that happen.

Stephen

Re: Plough plane question

#14

Ah -- that was my other problem. :@)

wilbur

>