Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

Arrangement of workbench and tool racks

Posts

Arrangement of workbench and tool racks

#1

Arrangement of workbench and tool racks

wilbur

>Does anyone have their shop set up in such a way that the workbench is close to but not up against a wall, and the wall has tool racks/cabinets along it's face? With this arrangement, most of your work at the workbench would be done standing between the bench and the wall.

My workshop is short on space (whose isn't?) and originally I was planning to have my workbench against one wall with tool racks on the wall itself. I've seen many examples of this. The down side of this plan is that my workbench depth will probably be limited so that I can actually reach the wall, and due to the short ceilings in my shop that only gives me about 3 vertical feet of storage space.

By moving the workbench away from the wall, I'll be able to have tool storage from floor to ceiling, and can make the top wider, and it will be easier to have the workbench serve double duty as an assembly table. The down side of this plan is that all the pictures I've seen where the bench is in the middle of the workshop are in workshops that are much more roomy than mine, which makes me think that realistically I won't have enough room to do this, in that the bench will need to be farther away from the wall than I think. Also, for this to work well, the face vise side of the bench would be aimed towards the tool rack wall, which would be an additional space cramping factor.

Thoughts?

Re: Arrangement of workbench and tool racks

#2

Re: Arrangement of workbench and tool racks

Chuck Nickerson

>Depending on your projects, you might need a lot of space between the front of your bench and the wall. If you mostly do small boxes then it's not an issue. If your bench will have drawers to store tools, you'll need room to open the drawer and stand and etc. One thought: how many tools need to be 'on the wall' handy? I've finally moved tools off the wall that I use a couple times a week or less.

Re: Arrangement of workbench and tool racks

#3

Re: Arrangement of workbench and tool racks

Roderick Drumgoole

>Wilbur,

Based upon the constraints of space that you are facing, I would not be to concerned about how various shops are viewed in pictures nor would I attempt to have tools in the percieved "ideal" location. A few months back PopWood featured an article on Rob Millard's shop in which he basically works from a small garage that houses his car at night. His shop didn't fit any model that I had seen as he has things everywhere in no particular arrangement that I could see. What impressed me about his set-up is that he takes what space he has (which is next to nothing), adjusts accordingly, and turns out beautiful Federal Period furniture. It reminds me of when I first started woodworking, in which I had this insatiable desire for many tools, preparing for the day that I would "need" them; three years later, and I kicking myself for the money wasted on tools in which I don't use and probably never will. I guess the bottom line, is only you know the space contraints that you are facing; take what you have, ensure that you have covered the essentials such as how things will fit in different locations, and go to working wood. I hope this helps!

Roderick

Re: Arrangement of workbench and tool racks

#4

Re: Arrangement of workbench and tool racks

Hank Knight

>Wilbur,

My shop arrangement is similar to what you describe. My shop is small (14' X 23'). I originally had my bench against the wall, but I fouind I liked it better in the middle of the floor where I can work all around it. I have a long bench for my radial arm saw against the wall and my workbench is situated parallel to it with about 3 1/2 feet between the two. I have cabinets and peg board above the RAS bench where most of my tools are stored. Here's a photo (ignore the short fat dude with the saw):

CUTTING LEGS TO LENGTH

It's a very handy set-up. I don't know why a set-up like you describe without the RAS bench wouldn't work. Also, as a bit of interesting errata, I've seen photos of Frank Klaus's shop and his bench is set up as you describe. Ellis might want to chime in here and comment on Frank's layout.

Hank

Re: Arrangement of workbench and tool racks

#5

Re: Arrangement of workbench and tool racks

wilbur

>Hi Hank,

Thanks! That picture helped me out a lot to visualize things.

One other problem with my storage situation is that in the part of my shop that I want to put my bench, the walls are also occupied with a doorway, water meter, and the circuit breaker, which also cuts into potential storage space.

Re: Arrangement of workbench and tool racks

#6

Re: Arrangement of workbench and tool racks

Moses Yoder in White Pigeon, MI

>I think the biggest problem we run into is not a lack of storage space, but having tools that aren't necessary. As has been mentioned. Mr. Schwartz mentions moving the bench around to where it's needed at the moment which is a good option. I like having the bench away from the wall and have a shelf with a number of tools on it and cabinets above the shelf, similar to what is show in Hank's picture. One thing I have found is that woodoworkers work on their shops a bit. It is part of the hobby. No matter how it is set up, in a few years you will come up with a different or better plan and make some modifications as you go along. I dislike the paralysis of designing the perfect layout and prefer to just get on with it after coming up with an excellent plan.

Re: Arrangement of workbench and tool racks

#7

Re: Arrangement of workbench and tool racks

Hank Knight in SC

>Moses hit the nail on the head. Part of the enjoyment is working on your shop. I've rearranged my whole shop 4 or 5 times in the last 10-12 years. I think I've finally found a configuration that works, but I may change my mind and move it again. Who knows? I learned one thing in the process: don't nail anything down permanently. As soon as you do, you'll decide it would work better over there. When I had the basement slab poured for my shop floor, I was certain my tablesaw would stay in the center of the floor. I ran conduit under in the concrete with an outlet for the saw smack in the middle of the floor. The saw stayed there for about two years. Since then I've moved it 4 or 5 times; each time it ended up nownere near the floor outlet. I've stumbled over that outlet a thousand times. Now, fortunately, it is situated sort of under my bench, so it's less of a hazard. I think that even if I built my ultimate dream shop, I wouldn't make anything permanent, except maybe the wall outlets. But I've changed and added to those in my current shop too.

Hank