Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

hand plane assembly - HELP!

Posts

hand plane assembly - HELP!

#1

hand plane assembly - HELP!

Rick Snyder

>Hello,

I just bought a #5 from Woodcraft. The plane was sharpened by them and a protective coating was put on the iron. I am have a heck of a time adjusting the iron. The bevel should be down.... Correct? The depth adjustment wheel should be turned counterclockwise "to the end" correct? Everytime I lock the lever cap down the front end of the plane raises up a 1/16th or so. The blade is exposed way to much at that point. Whats going wrong?? I have adozen wooden planes and never have a problem with adjustments. I love my wooden planes but want to use other ones as well. I would love to buy a Holtey!

Thanks for any advice. Rick

Re: hand plane assembly - HELP!

#2

Re: hand plane assembly - HELP!

Dan Donaldson

>Did you mean that the fron end raises or that the blade protrudes a bunch. If the front end is actually moving, I would be checking to see if I had a cracked casting.

Re: hand plane assembly - HELP!

#3

Dale Lenz

Re: hand plane assembly - HELP!

Dale Lenz

>Try adjusting the iron depth after you have lock the cap iron down. If I have misread your post, I'm sorry. Dale

Re: hand plane assembly - HELP!

#4

Dale Lenz

Re: Edit: lever cap NOT cap iron

Dale Lenz

>

Re: hand plane assembly - HELP!

#5

Re: hand plane assembly - HELP!

Bruce, a MN Galoot

>How close do you have the leading edge of the cap iron to the edge of the blade? If you have too much blade extending beyond the edge of the cap iron, then you're going to get too much blade sticking out the bottom of the plane because the adjustment mechanism registers on the slot of the cap iron.

Bruce

Re: hand plane assembly - HELP!

#6

Re: hand plane assembly - HELP!

Wiley Horne -- So. Calif.

>Rick said,

"Everytime I lock the lever cap down the front end of the plane raises up a 1/16th or so."

________

I'm having a time trying to get my head wrapped around this statement. When you lock the lever cap, the lever is pulling the sole, the frog, and the blade/cap iron assembly tight together. The whole assembly is anchored in the sole (unless it's a bedrock design).

Is it possible that the sole is sufficiently warped, that the pull of the lever cap in the middle of the sole is causing the sole to deform? If it's moving 1/16", then you can watch and see exactly what is happening as the lever is locked down. Try it and report back, please.

Wiley

Re: hand plane assembly - HELP!

#7

Re: hand plane assembly - HELP! #2

Rick Snyder

>Hello again,

I'm sure this is operator error at its best.

Questions.....

1- Is the bevel of the iron up or down (as you look at it in the plane?

2- How far is the chipbreaker from the edge of the iron?

3- How tight is the chip breaker to the iron?

4- Currently I have the Depth adjustment wheel turned all the way tight(end) (counter clock wise)

At this point I can't explain it any better. I have a Woodcraft not to far away. Might just stop in and watch the assembly first hand.

Thanks for all the responses so far. (this has been a "Murphys law" day today).

Thanks again.... Rick

Re: hand plane assembly - HELP!

#8

Re: hand plane assembly - HELP! #2

Wiley Horne -- So. Calif.

>Hi Rick,

Stopping back by Woodcraft would make sense, cause they should have done a few shavings with you in the first place.

On your questions:

1- Is the bevel of the iron up or down (as you look at it in the plane?

The bevel is down. The chipbreaker is on top of it, which means that the bevel side of the blade is sitting on the frog.

2- How far is the chipbreaker from the edge of the iron?

This is not critical (at this stage), but say 1/16" is fine. What is important is that the little tang on the end of the depth adjust assembly is passing through the blade slot, and is engaging the little hole in the chipbreaker.

3- How tight is the chip breaker to the iron? Not critical at this stage--it can be screwed tight with no harm. Much can be said about adjusting chip breakers, but right now we're still trying to get the plane to work.

4- Currently I have the Depth adjustment wheel turned all the way tight(end) (counter clock wise)

This may be an issue. There's no rule about turning the depth adjust wheel all the way counterclockwise. You set the depth adjust wheel so that the little metal hook or tang passes through the blade and engages a hole in the chipbreaker. Turn the depth adjust wheel to a place where that tang will engage the chipbreaker hole. There's no preset location--by inspection, you just look where the tang is relative to the chipbreaker hole, and turn the wheel until it engages nicely.

You then adjust the tension on the lever cap screw so that you can raise and lower the blade assembly with the lever cap clamped down. That is, the lever cap should allow movement of the blade assembly as you turn the depth adjust wheel. If it won't, loosen the lever cap screw until it will. But it is the engagement of the tang in the chipbreaker that makes the blade assembly move.

Wiley

Re: hand plane assembly - HELP!

#9

OK let's see here...

Scott Burr in Ben Lomond CA

>One question for you Rick, Who made this plane?

Here's some answers:

1. If it's standard No. 5 the bevel should face down (if there's a makers mark on the blade you should be able to see it when the blade is installed in ther plane.

2. Around 1/16 of and inch from the edge of the blade.

3. Thight, you should see no gap(or light) between them.

4. Back it off a few turns and see what happens.

Re: hand plane assembly - HELP!

#10

One additional issue

Bill Houghton, Sebastopol, CA

>I'm not sure this could be causing your problem, but I'll throw it in as a part of good practice.

There should be a lever coming up from the frog (in case you're unfamiliar with plane terminology and are looking for a green thing saying "ribbit," that's where the cutting iron, aka "iron," sits) over top of the tote (back handle) that can move sideways. At the other end is a little wheel (good planes) or wide spot (cheaper planes) that engages in the slot of the plane iron. It's really easy to set the iron down so that this doesn't engage, and then nothing will work right. As you put the plane iron on the plane, kind of wiggle it around a bit until you feel everything engage - you can tell. Then put the lever cap on and snap it down.

If there's no such lever, you've got a plane that's either REALLY cheap (take it back and get your money back) or defective (ditto).

Re: hand plane assembly - HELP!

#11

Re: One additional issue

Stuart Hough

>One other possibility...are the screws that hold the frog to the base tight enough? It may sound too simple, but we beginners learn the hard way.