Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Shop built Marking knives and awls

Posts

Shop built Marking knives and awls

#1

Shop built Marking knives and awls

Dominic Greco in Richboro PA

>Hello Everyone,

Here are a couple marking knives and awls I made over the past week. The first one was made from some spalted Dogwood. It had some any holes that were filled with epoxy and coffee grounds. The ferrule is a 3/8" brass compression nut that was turned smooth. The "blade"is a section of HSS left over from a bunch I had purchased from ENCO last year (I made some 3 point turning tools). Since the wood was so "busy looking", I kept the shape simple.

After this success I decided to get fancy and cut up an old planer blade and formed (2) marking knife blades. I made a simple jig to work with my Veritas Grinder Tool Rest and ground the edge. Then I got fancy and honed and polished the faces so that they shone. I then used some ebony, and some bubinga scraps to make the handles. Like before, I used compression nuts as the ferrules.

It's pretty much the same story with the bubinga awl as with the dogwood one. Except I used a section of 3/16" HSS rod as the blade. I wanted something with a bit more heft, and a steeper angle to the point.

I admit, I went a bit over the top when it came to sanding. All were sanded to 15000 grit (micro mesh). I guess that's my old pen turning influence showing up again!

The finish is multiple coats of Watco's Danish Oil followed by a coat of Renaissance Wax.




Thanks for Viewing!

See ya around,

My ugly mug


Dominic

Re: Shop built Marking knives and awls

#2

SWEET!

Scott Burr in somewhat warn Ben Lomond, CA

>Hey Dom, You did yourself good! Those look wonderfull! How long are the marking knife blades?

You've made a very nice addition to you layout tools if I do say so myself. Did you design them on SolidWorks? Errrr SolidEdge? Them plastic lookin' CAD programs look the same to me;^)

Re: Shop built Marking knives and awls

#3

Whoa!

Tom Colligan

>

Re: Shop built Marking knives and awls

#4

Re: Shop built Marking knives and awls

Stephen Shepherd in the State of Deseret

>Nice work Dom, have you ever made square awls?

Now I probably won't enter the Tool Making Contest.

Stephen

Re: Shop built Marking knives and awls

#5

Re: SWEET!

Dominic Greco in Richboro PA

>Scott,

Thanks for the compliments!

You wrote:

"How long are the marking knife blades?"

Sorry I should have mentioned dimensions! The blades are 1/2" wide x approx. 1" (ebony) to 1 3/8" (bubinga) long x 1/8" thick. The entire knife is about 6" to 6 3/8" long. The handles are about 5/8" in diameter at their widest.

I didn't use ANY solid modeling for these bad boys. The entire design came right out of the old noggin'!

BTW, I'm using Inventor now. So I got another program to add to my resume! :>)

See ya around,

Dominic

Re: Shop built Marking knives and awls

#6

Square awls? Hmmmmmm

Dominic Greco in Richboro PA

>Stephen,

Thanks for the compliments!

I'm assuming that when you say "square" you mean the iron would be square in cross section. Right?

If so, I guess I could make a square awl easy enough. Hell, all I'd need is an appropriate piece of steel. And I could get that from ENCO. And I think the square cross section would mean it would be a bit easier to hone the point.

Now you have me curious. What are the other advantages to a square awl?

BTW, funny you should mention the tool making contest. I just entered the bubinga set of tools about 10 minutes ago.

Dominic

Re: Shop built Marking knives and awls

#7

Re: Square awls? Hmmmmmm

Stephen Shepherd in the State of Deseret

>Well of course square awls are good for square nails, although I use a brad awl (you should consider making those as well) which is round with a double bevel chisel point.

The greatest advantage besides the flat edge of a square awl rides nicely along a straight edge (well so does a round one) but it is a little easier to keep it straight I think, is that it can be used to ream out holes, it has four cutting edges. (Or does it have eight if you use it in both directions?)

I also make handles that have at least one flat side so they don't roll off the bench.

Stephen

Re: Shop built Marking knives and awls

#8

Re: Square awls? Hmmmmmm

Derek Cohen (in Perth, Australia)

>Hi Stephen

By "square awl" are you referring to a "birdcage awl"?

You can make these easily enough by grinding four facets to the end of a rod.

Regards from Perth

Derek

Re: Shop built Marking knives and awls

#10

Thank you Derek!

Dominic Greco in Richboro PA

>Derek,

Thanks for the compliments! They really mean a lot coming from you since you were the inspiration for making the knives.

I downloaded the article on making a marking knife from your site and was planning on making one just like yours. However, somewhere along the line the "creative juices" started to flow and I started using my own ideas. :>)

See ya around,

Dominic

Re: Shop built Marking knives and awls

#11

Not a bad idea.....!

Dominic Greco in Richboro PA

>Stephen,

Now you got me interested! I like the fact that the flat side of that style awl can ride along a ruler. I think I'm going to look into getting a piece square stock and give making that style awl a shot.

Thanks for the "push"! :>)

See ya around,

Dominic

Re: Shop built Marking knives and awls

#12

Re: Shop built Marking knives and awls

Dave Anderson NH

>Absolutely beautifully done Dom. Gettin' the tool making bug now?

Re: Shop built Marking knives and awls

#13

I've had it for a while!

Dominic Greco in Richboro PA

>Dave,

Thanks for the compliments!

And I've had the tool making bug for a long time now. I've made a bunch of turning tools. But this is my first "real" shop built hand tool.

See ya around,

Dominic

Re: Shop built Marking knives and awls

#14

How do you cut the steel

Stephen in Ottawa

>Great work. I've been wanting to make a marking knife for some time now. Thinking of using a jig saw blade. The hardest steel I've cut so far is saw steel. How does one go about cutting the jigsaw blades, planer blades etc.?

- Stephen

Re: Shop built Marking knives and awls

#15

Dremel and abrasive discs

Dominic Greco in Richboro PA

>A Dremel and an abrasive disc made short work of the steel. Be sure to wear eye protection and try not to shoot the sparks down the front of your shirt! DAMHIKT.

See ya around,

Dominic

Re: Shop built Marking knives and awls

#16

Great...

wilbur

>that's all I need. One more reason not to enter the tool making contest.

Actually, two.

Nice work!