Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Odd Stanley Block Plane 1 of 5

Posts

Odd Stanley Block Plane 1 of 5

#1

Odd Stanley Block Plane 1 of 5

charle belden

>Picked up this odd Stanley plane tonight. Looks sort of like a block plane - and has an adjustable throat - but has some odd features.

First is the mechanism for moving the iron "in ' out". Not like any mechanism I've seen.

Second, the cam action "palm handle" / "lever cap" / "chip breaker".

Other than "STANLEY" on the "lever cap / chip breaker" and a "B" on the underside of the palm "handle", there are no other marking on any of the parts.

Anyone know what this little beasty is and perhaps when it was in production?


img

Re: Odd Stanley Block Plane 1 of 5

#2

Re: Odd Stanley Block Plane 1 of 5

Todd Hughes

>Is acording to it's size a Stanley no. 18 or 19 Knuckle Cap block plane [18 is 6 inch long the 19 7 inch]...from your description and photos looks like it was made between 1900 and 1910, Befor 1900 they had the side "Hump" more toward the back of the body and after 1910 they had Stanley cast into the body by the front knob.

These knuckle cap block planes are very common planes through I don't see to many older examples that are in very good condition .....Todd

Re: Odd Stanley Block Plane 1 of 5

#3

Blade adjustment mechanism

Bill Houghton, Sebastopol, CA, sunny so far!

>The vertical post adjuster was the commonest type for "standard angle" - 20 degree - Stanley and similar block planes. The modern makers like Lie-Nielsen and Lee Valley have, probably rightly, gone in the direction of using one blade adjustment mechanism for all their block planes, regardless of angle, although each maker uses a slightly different mechanism.

Re: Odd Stanley Block Plane 1 of 5

#4

Re: Odd Stanley Block Plane 1 of 5

charlie belden

>Got the tape measure out. 7" long and a tad over 1 7/8" wide, so now it looks like it's a #19. The iron is 1 5/8" w and a bit under 4 1/2" long. The 1902 catalogue gives the iron width as 1 3/4", not 1 5/8" - but the iron fits the body which is a bit under 1 3/4" wide inside where the iron sits.

Slick little block plane. A little big to carry around in a pocket, but I like the knuckle handle fingered cam locking mechanism - all movement straight down, no twisting / rotation like on some of the other locking mechanisms.

A little cleanup, a bit of checking for flat and square and this puppy goes in the wall cabinet of user hand tools, above a #60 and a LN rabbet/block plane (ah - the look of shiny polished brass!).

The idea of putting a tool. probably made right at the turn of the 19th century, back into service is kind of a nice thing.

I know wood "talks" - I've had several conversations with boards. Wonder if hand planes talk.

SHHHHH! I'm trying to listen.

Re: Odd Stanley Block Plane 1 of 5

#5

Re: Odd Stanley Block Plane 1 of 5

Bill Houghton, Sebastopol, CA, sunny so far!

>Those long block planes are good shop tools. The extra length makes for easier gripping two-handed, when that's the right approach, and extra mass for planing.

I have one that came with that type of knuckle-joint cap, and it kept popping off in use. Yours may be in better condition, but if you have that problem, the solution is to get the later model knuckle joint cap, which is a wondrous thing.

I look at the LN and LV block planes in the catalogs from time to time, but am not convinced I'd be better off with one over my #18 and #65.