Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Pegged joints

Posts

Pegged joints

#1

Pegged joints

Denis Ch�nard, Orl�ans, Ont.

>I was just reading June 2007 FWW, in which there's an article by Matthew Teague on pegged joints. In it he claims that pegged joints are stronger than non-pegged ones.

I am skeptical...

I think I remember reading some article on joint strength, where the presence of the peg was shown to induce a weakness on the walls of the joint. And that's where the joint broke IIRC.

If one thinks about it, if the glue is stronger than the wood (as it should be), any "disturbance" on the wood side will only weaken the wood part.

Has anyone done tests on that? Or is it irrelevant, given that even a pegged joint is strong enough?

Curious here...

DC

Re: Pegged joints

#2

Re: Pegged joints

Warren in Lancaster, PA

>If you use hide glue the peg will keep the joint together if the glue should loosen. The presence of a peg also tends to keep people from putting nails through the joint which can make disassembly difficult. One nail can sometimes double or triple the cost of repair. If you use a glue other than hide glue, you are making throwaway furniture; nobody will want to repair it if they can't get it apart and clean the joint.

Re: Pegged joints

#3

Re: Pegged joints

Brad in Ottawa

>Check out Woodworking Magazine. I can't remember the date of the issue but it is the issue that has an inlayed mirror on the cover that incidentally is one of the projects inside.

There is an article in there on pegged joints that discusses these joints in depth. I cannot recall anything regarding strength but I do know that it discussed placement of the peg can have an adverse effect.

HTH,

Brad

Re: Pegged joints

#4

Re: Pegged joints - follow up

Brad in Ottawa

>I quickly scanned the article this morning and it was an instructional article on making pegged joints. Poor placement of the peg would weaken the joint. (But then again, poor placement/sizing of the mortise/tenon would weaken the joint too!)

They did mention that glue provides strength but the mechanical strength (i.e. fit) of the joint adds more strength to the joint than glue. The inference being that a pegged joint would add mechanical strength.

Again, no testing references!

Re: Pegged joints

#5

Re: Pegged joints

wilbur

>I think that the primary advantage of a pegged mortise and tenon joint is that the holes in the mortise and the tenon that the peg goes through are offset by a little bit. When you bang the peg into the holes, the offset draws the shoulders of the tenon up tight against the piece with the mortise. This may not affect the strength of a perfectly fitted mortise and tenon joint, but it should increase the strength of a mortise and tenon joint that is a little loose, such as the ones I always seem to make. :@)

The other advantage is that the peg makes the joint self clamping.

Re: Pegged joints

#6

Re: Pegged joints

Walt Turpening

>I use pegged mortise and tenons on my benches, stools and chairs. The glue is fine and holds well, however, the majority of my customers are weavers who are fairly dynamic while weaving: moving side to side and front to back. As such, I have seen flexing of the frame that could work the stretchers in the legs. So I have added a peg for sometime in the future if the glue does finally give out and the wood has shrunk there is some extra mechanical connection.

Using wood pegs, at least they can be drilled out the joint repaired and repegged. In over 10 years of bench making (500+ benches, stools and chairs) only one joint has failed. I was able to repair it and have it back to the cutomer the day after it arrived in the shop.

Walt T.

Benches, Stools and Chairs

Re: Pegged joints

#7

Re: Pegged joints

Verne in NJ

>Recently I went to the Cloisters in NYC. They have a collection of medieval furniture. The joints? All pegged. Still together, most still tight 500+ years later.

I wonder if Titebond will fare as well! ;-)

Re: Pegged joints

#8

Re: Pegged joints

Stephen Shepherd in the State of Deseret

>No, But hide glue will.

Stephen