Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

Preparing a board without a thicknesser-planer-joi *LINK*

Posts

Preparing a board without a thicknesser-planer-joi *LINK*

#1

Preparing a board without a thicknesser-planer-joi *LINK*

Derek Cohen (in Perth, Australia)

>Preparing a board without a thicknesser-planer-jointer

This article has just gone up on my webpage (link below).



It is aimed mainly at newbies to handplane use, but may have a wider interest. There are many ways to do this task - this was one slice of time in an afternoon. Comments, alternatives, and discussion are always welcomed.

Regards from Perth

Derek


Preparing a board without a thicknesser-planer-joi

Re: Preparing a board without a thicknesser-planer-joi *LINK*

#2

Jack Guzman from Maine

Nice tutorial

Jack Guzman from Maine

>That's a keeper Derek. Besides being very informative, that was easy to navigate,even with my slow internet connection and clunky computer. Thanks for posting it.---Jack

Re: Preparing a board without a thicknesser-planer-joi *LINK*

#3

Re: Preparing a board without a thicknesser-planer

john lucas

>Thanks for that link. We have a new woodworking club that we just started and have many beginners. We meet in a golf clubhouse so we don't have machines available. I've been working on demos that we can do at the clubhouse. Hand plane use as well as tune up is on the top of my list.

Re: Preparing a board without a thicknesser-planer-joi *LINK*

#4

Re: Preparing a board without a thicknesser-planer

guy in US

>Derek,

I appreciate all your on-line articles at wkfinetools and other forums. But I'm unclear about one step in your documentary. You show the edge as jointed to 90 degrees with the flattened face, but i do not see a fence on your jointer. Was this also done by sighting the high and low spots?

Are the sides of your jointer square enough to clamp (or screw) a right angle fence to it?

Thanks for sharing.

GB

Re: Preparing a board without a thicknesser-planer-joi *LINK*

#5

Re: How much time did it take

Wayne

>I did a piece of rough cherry the other day to see if I could, it was very gratifying. It makes one appreciate the labor that went into the Highboys and other furniture the was made way back when. Nice article what kind of wood were you working on? very pretty grain.

Re: Preparing a board without a thicknesser-planer-joi *LINK*

#6

Re: Preparing a board without a thicknesser-planer *LINK*

Derek Cohen (in Perth, Australia)

>Hi GB

I could have included more pictures (had I thought to take them - there were some things that I just took for granted). Squaring and jointing an edge seems such a basic task that I am guilty of overlooking the fact that it is actually quite difficult to do when starting out.

To joint the edge I simply planed it by eye, using the 6" square in the picture to help determine how much more needed to be done, and where. This was simply done by checking different points of the edge.

I do have a couple of fences for jointer planes, and they all work pretty well, but I rarely use them much. I'd probably pull out the Stanley #386 if I wanted the bevel an edge at a non-standard angle. Here is the #386 on a jack ...



Alternately, there is the fence that attaches to the Veritas BU Jointer. For a detailed description and depiction of this in use, see the Link below.



Regards from Perth

Derek


The Veritas Bevel-Up Jointer Fence

Re: Preparing a board without a thicknesser-planer-joi *LINK*

#7

Re: How much time did it take *LINK*

Derek Cohen (in Perth, Australia)

>Hi Wayne

The day I did this was warm, very warm ... about 100 F. My workshop is in a brick double garage, without a ceiling and just rafters and clay tiles. Not a lot of protection from the heat of summer. So I was in-and-out of the workshop quite frequently. This makes it harder to judge the amout of time actually spent on this particular task. I'd estimate about 1 hour is the usual time for a board like this. 90% of this is really the amount of time spent trueing up the rough timber. Once the bandsawing begins it is a speedy affair.... saw ... re-plane face of timber ... saw ... re-plane face of timber ... saw ....

The wood is She-oak. This is a member of the Casuarina (Casuarinaceae) family. West Australian sheoak is a highly figured honey coloured timber which is very stable.

I have supplied a link (below) formore detailed info. The article notes "Saws with difficulty and also difficult to work with hand and machine tools because of the high density Finishes smoothly."

Regards from Perth

Derek


She-oak