Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Neander buddy needs a new blade.

Posts

Neander buddy needs a new blade.

#1

Neander buddy needs a new blade.

Scott Burr in Ben Lomond CA

>Warning power tool content (kinda)!

My Timberwolf 1/2 3 TPI resaw blade has finally bit the dust.

I'll admit I'm not too keen on resawing by hand. I liked the Timberwolf blade, but there are new blades out in the workd now.

Lenox, Woodslicer, etc.

Do or have any of you used these? How do they compaired to Timberwolf blades?

My BS is a 14" Delta with a riser.

Cheers,

Scott

Re: Neander buddy needs a new blade.

#2

Re: Neander buddy needs a new blade.

Denis Ch�nard, Orl�ans, Ont.

>Got the same saw, used Timberwolf blades until I tried a Woodslicer. Much better, cuts so smooth that you have to look twice to find what side of the wood piece was cut. Quieter, thinner kerf, lower power requirements. A real winner in my book.

DC

Re: Neander buddy needs a new blade.

#3

Re: Neander buddy needs a new blade.

Glenn Madsen near San Francisco

>I got a Lennox blade, same config, for the 16" Jet bandsaw I used to run, and it did really well for me. The 3/4" seemed even better for wide resaws, which were few. Saw went to a friend that needed it more than I did, though.

The news today had it raining pretty hard there in the Santa Cruz Mountains. You doing all right?

Re: Neander buddy needs a new blade.

#4

Re: Neander buddy needs a new blade.

Bruce, a MN Galoot

>I have the same saw, use a Lenox Trimaster. I've had that blade on the saw for more than 2 year, still works great, even after I resawed a sheetrock screw.

Bruce

Re: Neander buddy needs a new blade.

#5

Re: Neander buddy needs a new blade.

Todd O. Cronkhite Maine Native, Presently Away

>There is another blade out there called Olson, or Olsen, can't remember the correct spelling, that also got decent reviews. Don't know how well they'd perform after resawing sheet rock screws tho. ;~)

T.O.

Re: Neander buddy needs a new blade.

#6

The Trimaster is carbide tipped

Bruce, a MN Galoot

>Helps with those pesky sheetrock screws

Re: Neander buddy needs a new blade.

#7

Thanks Dennis, I've heard good things about them!

Scott Burr in fridgid Ben Lomond, CA

>

Re: Neander buddy needs a new blade.

#8

Barely...

Scott Burr in fridgid Ben Lomond, CA

>Pulled down 3.5 inches last nignt. Came home to a full rain gauge that fills up at 5.5".

Early today after a driving to SJ @ 6:00am this morning, that was a fun commute!

Dodged a mud slide and 1 downed tree. Left work at 12:30pm to find hwy 17 a waterfall past the Cats resturant. Got home after a few blacked out signal lights and a stop for a couple beers at 2:30 not to bad all things concidered. The power came back here around 7:00pm, thank god for Chinese take-out!

One thing about us neanders, I put some work on the box I'm making for my new marking knifes untill it was too dark to see!

OK, I've heard that the Lenox carbide tips don't like 14" wheeles, tend to pop off. Guess that extra 2" counts for something!

Re: Neander buddy needs a new blade.

#9

OK Bruce, time to spill it...

Scott Burr in fridgid Ben Lomond, CA

>Resawing drywall screws? Common' man inquiry minds...

The Lenox blade is sounding like a good choice IMHO.

I'm still conserend about the tales of the teeth comming off on a 14" saw...

Or is that because of drywall screws?

Re: Neander buddy needs a new blade.

#10

Re: OK Bruce, time to spill it...

Bruce, a MN Galoot

>Well, it wasn't quite intentional. Someone (to remain nameless) picked up a piece of scrap to use for a jig. That certain someone had done a quick, but not thorough, check of the wood for things like screws, but this particular offender had the head snapped off so it wasn't apparent. I guess the sparks should have tipped me off.

BH,

Re: Neander buddy needs a new blade.

#11

Thanks everybody!

Scott Burr in Ben Lomond

>After a little investagation I went with the Woodslicer. The Lenox looked realy good but at $120.00 it was a bit rich for my blood.

So I got a total BS tune-up for the cost of the Lenox blade. 2 new tires, ball bearing guides, wheele brush, Iturra spring and a new woodslicer for about the same ammount of cash.

That girls gonna rock now!

Thanks again for all your help!