Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Homebuilt lathe 1of 5

Posts

Homebuilt lathe 1of 5

#1

Homebuilt lathe 1of 5

Todd O. Cronkhite Maine Native, Presently Away

>OK, here's some pics of my homebuilt lathe as per Bill's request. I'm going to do my best to include allot of the demensions and other info just in case somebady may be interested in building one. If I leave anything out, and I probably will,or if you have any questions feel free to ask for more info or pics.

I built the lathe in '95 from the plans I found in a book that was put out by WOOD magazine.

-All the plywood used was 11/16" thick

-I ordered the hardware from the company that is listed with the plans. The hardware included the 2 #2 MT shafts, the pulley on the shaft, the 2 headstock bearings, and the belt. Cost was #200

-The motor is a flea market special 1/2 h.p. 1725 rpm 110v single phase.

-The motor is bolted to a board, with common strap hinges bolted to the board, then to the backside of the base. It's own weight keeps the belt tight.

-The bed rails are 70" long, by 7 1/8" wide.

-Each rail is made up of 3 strips of 11/16" plywood

-The gap between the rails is 2 7/8"

-The bolts are common carriage bolts.

-The towers that hold the shafts are 5 1/2" x 5 3/4"

-Between the rails is a block that is 10 3/4" long

-The towers extend 11" above the rails, and 3 14/16" below in the center of the rails.

-The center of the shafts are 8 3/4" above the rails.

-The shafts in the tail stock are threaded thru two common floor flanges that I rethreaded with a 1" 8 thread per inch tap.

-The distance between the center of the motor shaft and the headstock shaft is 25"

-The two bases are hollow and are 27 3/4" tall, at their bottoms they are 15 1/2"x11 3/8", at the tops they are 11 1/2"x8 3/16"

-I had to extend the rod of the tool rest to accomadte the extra dept of the rails. I did this by merely using a thread union and a lenght of all thread.

-I had to make riser blocks to put beneath the tool rest itself to raise it up to reach the shafts. It's a bit of a pain when it's time to reposition it, but for the add'l depth that I can turn it's worth it. The riser blocks as you can see are just two pieces of 2x4 screwed together.

It's been a good lathe, and don't regret building it. I like the idea that by building it myself I can change the dimensions of it if I so choose.

T.O.


img

Re: Homebuilt lathe 1of 5

#2

Re: Homebuilt lathe 2of 5 

Todd O. Cronkhite Maine Native, Presently Away

>


img

Re: Homebuilt lathe 1of 5

#3

Re: Homebuilt lathe 3of 5 

Todd O. Cronkhite Maine Native, Presently Away

>


img

Re: Homebuilt lathe 1of 5

#4

Re: Homebuilt lathe 4of 5 

Todd O. Cronkhite Maine Native, Presently Away

>


img

Re: Homebuilt lathe 1of 5

#5

Re: Homebuilt lathe 5of 5 

Todd O. Cronkhite Maine Native, Presently Away

>


img

Re: Homebuilt lathe 1of 5

#6

Re: Homebuilt lathe 1of 5

Jeff S.

>Todd,

Thanks for posting the pictures. I saw that lathe at the fringe of a previous picture and was wanting to see more myself.

It is a great example of Yankee ingenuity, looks quite stout and up to the task!

Jeff

Re: Homebuilt lathe 1of 5

#7

Neat!

Bill Houghton, chillyish Sebastopol, CA

>Nice work. Too bad you built it so long ago, or you could enter it in the tool-making contest.

Re: Homebuilt lathe 1of 5

#8

Very cool but, hey Todd...

Scott Burr in fridgid Ben Lomond, CA

>How's she work?

Scott, who must admit a lathe would be a neat addition to the shop...

Or should I outsource chisel handles to you?

Re: Homebuilt lathe 1of 5

#9

Cover that Belt!

Jorge Castaneda~Downeast Maine

>Good work Todd,

Safety first, cover the belt.

Show us another pic with lots of shavings...

Jorge

Re: Homebuilt lathe 1of 5

#10

Jack Guzman from Maine

Wow!

Jack Guzman from Maine

>That is an ambitious project.Nicely done Todd. One question,how do you keep the belt aligned when changing speed with that multiple pulley?---Jack

Re: Homebuilt lathe 1of 5

#11

Re: Wow!

Todd O. Cronkhite Maine Native, Presently Away

>Jack,

The belt stands in alignment by changing it in both the headstock groove and the motor shaft groove. Granted I only have 4 different "speeds", but they have been more then adequate. I at one point was going to get a motor that I could hook up as variable speed, then that way I'd have hundreds of different speeds, but at the time it got to the point where it seemed to be more hassle then it was worth.

Yeah Jorge, I know that open belt looks scary, but really it hasen't been a problem or a danger---yet. I do need to rig up a guard for it I will agree.

Scott, I'll make some shavings with it shortly. I haven't done any turning for a long time, and truth be told I'm ready to take 'er for a spin. OK, that was a cheap pun, but hey, it's 6:30 a.m..

T.O.

Re: Homebuilt lathe 1of 5

#12

More info re headstock bearings please

Patrick Gibbons, Houston, TX

>Where did they come from? What are they, that is, ball bearing? babbit? How much?

Re: Homebuilt lathe 1of 5

#13

More info re headstock bearings

Todd O. Cronkhite Maine Native, Presently Away

>Patrick,

The two headstoack bearings are 1" Flange Bearings with locking collars.

I got the hardware kit which consisted of the the two 1" shafts, the two flange bearings, the 1" 4step pulley and the 60 " cogged belt from a company called: Northwest Carving Supplies, P.O. Box 407, 123 W. Railroad Ave. N, Manhattan MT 59741 Telephone # 406-284-6009

I have no idea if this company is still in business, but that is where I ordered mine from back in '95.

The flange bearings should be available thru any hardware supply dealer I would think, as withthe pulley and the belt. The shafts where the real specialty item.

HTH, and if you decide to build one give me a shout for any add'l info/pictures.

T.O.


img

Re: Homebuilt lathe 1of 5

#14

Belt

Bill Houghton, rainy Sebastopol, CA

>"Yeah Jorge, I know that open belt looks scary, but really it hasen't been a problem or a danger---yet."

No, and running stop signs isn't a danger either, right up to when you T-bone a semi-truck carrying propane.

I've run unguarded belts myself, but am increasingly aware of how quickly you can get caught in one. Your design would be very, very easy to mount a guard on, and you could make one from plywood scraps without noticeably changing the looks of the lathe.

Re: Homebuilt lathe 1of 5

#15

Re: Belt

Todd O. Cronkhite Maine Native, Presently Away

>Yeah Bill, I was thinking of a design that you cover the belt, and be easy to change the belt to new positions. that is the one drawback to this design--you have to manually change the belt to change speeds. Still, for the amount of money that I didn't spend for a alther this size, plus one I can alter so easily if I so need or desire, this is of no consequence.

There was a guard in the plans,but I didn't build it as I didn't like it. I guess I will come up with something so you and Jorge can sleep well at night. ;~)

T.O.

Re: Homebuilt lathe 1of 5

#16

Re: Belt *LINK*

Pam Niedermayer - Austin, TX

>I don't know if the amps are right for your lathe, but one or both of these router table speed control accessories may work for you in avoiding belt shifting.

Pam


router table accessories at Japan Woodworker

Re: Homebuilt lathe 1of 5

#17

Re: Belt

Todd O. Cronkhite Maine Native, Presently Away

>Thanks Pam, I'll have to investigate that. I knew of these, but was under the impression that they wouldn't work for some reason. I figure if it does, and what with the four different pulley positions I can set the belt at, that I should have ga-zoodles of different rotation speeds.

T.O.

Re: Homebuilt lathe 1of 5

#18

Speed controls

Bill Houghton, rainy Sebastopol, CA

>Router speed controls work only with brush-type (aka universal) motors, as commonly found in routers and other hand held power tools. I believe they're potentiometers that reduce voltage to the tool and thus speed. Except for benchtop and jobsite table saws and suchlike, most stationary power tools use induction or other non-brush-type motors, and, as I understand it, reducing voltage to that type of motor won't change speed, but could damage the motor.

Re: Homebuilt lathe 1of 5

#19

safeties in the odds, why not improve them?

Cooper Suter

>Not to come on heavy, it is a cool lathe.

But....

The old stand by;

"I've done it this way a thousand times,........ first time I ever lost a finger." (or hand, or arm, or eye, or killed someone, etc.)

In those instances (assuming a person has a conscience) the best case is if it's your own finger, hand, arm, or life, not someone else's.

No telling who could be around that belt. Got any kids?

Coop

Re: Homebuilt lathe 1of 5

#20

Patrick, In Houston it's Purvis Bearings

VLParisian

>take the shaft you plan to use with you. might also print the picture Todd provided. Four bolt flange is very common, but they come in a lot of different sizes and duty types. Most likely they will have what you need in stock.

Re: Homebuilt lathe 1of 5

#21

Re: Speed controls

Pam Niedermayer - Austin, TX

>Thanks, Bill, I've been putting off trying one on my little hand made lathe motor. Looks like a motor choice is needed.

Pam

Re: Homebuilt lathe 1of 5

#22

and

Bill Houghton, Sebastopol, CA, drying out a bit

>You want the bearing on the "near" side of the headstock, the side facing the work, to be able to take thrust (axial pressure). A lot of bearings can't take thrust loads, or at least not for very long. If you get the right kind of bearing for that side, the other bearing needs only to be able to take radial pressure and will probably be cheaper.

Re: Homebuilt lathe 1of 5

#23

That's interesting,

Todd O. Cronkhite Maine Native, Presently Away

>I didn't know that Bill. I just ordered the hardware from the mentioned supplier. Something to keep in mind for future bearing purchases.

T.O.