Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Price drop on over 1300 Rockler items

Skew Chisel Sharpening

Posts

Skew Chisel Sharpening

#1

Skew Chisel Sharpening

Doug Reynolds in Seattle

>Is there an easy way to sharpen a Japanese skew dovetail chisel? Mine are too short to use in the Veritas skew jig and the blades are only about a 1/4" so, not much surface to register against. I'd like to make a jig so I can repeat the angle, both left and right skews at 45 degrees.

Re: Skew Chisel Sharpening

#2

Honing?

jim reed @ tallahassee

>I guess you are referring to honing on a stone. I would do that freehand. If you are set on using a jig, the easiest would be a scrap of wood with a hole drilled at the appropriate angle. Use a golf tee or sharpened dowel to wedge the chisel at the top of the hole. Good luck.

Re: Skew Chisel Sharpening

#3

Re: Skew Chisel Sharpening

ThomD

>I like to sharpen low surface area tools on harder stones, choose your own prefered type. One thing you can do is rest the hone on some object so the stone surface you are using is vertical and on your left. Rest the chisel handle on your table, and controling the end with your finger rotate it up and down over the surface. This takes the weight of the handle out of play and makes control easier.

Another thing you can do is use a slip stone. Move the stone while holding the chisel still.

Make your motions such that they excavate a hollow in the center of the chisel bevel, even though you are using a flat stone. Impossible of course, but it will stop your rounding the bevel, or I hope so.

Re: Skew Chisel Sharpening

#4

Skew Chisel Jig *Pics*

Donald Pierson

>Doug I made jigs for my chisel sharpening. Here are two picutures of a jig I use for one of my skew chisels. I made jigs for each chisel whether skew or straight. The help stop the twisting I have had using the Veritas MKII guide. The twisting tendency is reduced when the two thumb screws are tighten eveningly.

Photo Sharing and Video Hosting at Photobucket

Photo Sharing and Video Hosting at Photobucket

Re: Skew Chisel Sharpening

#5

Re: Skew Chisel Sharpening

Friedrich Kollenrott

>You don't need no jig. Sharpenung skew chisels freehand does not require witchcraft at all. Shown (below) is a 12"- chisel. Ground (freehand) on a 800 grid waterstone, the microbevel honed (freehand) on a 8000 grit waterstone. It shaves well.

The sharpenig took less than five minutes, taking the photo much more.

Friedrich Kollenrott, Extertal (Germany)


img

Re: Skew Chisel Sharpening

#7

wow, Nice job there.

vlparisian in Houston

>

Re: Skew Chisel Sharpening

#8

Re: Skew Chisel Sharpening *LINK*

Brent

>If you are prepared to make a wooden jig, you can probably adapt the design of my slanted jig to your problem.

You will have to spend some time on the jig extension page to figure out the appropriate jig angle for the chisel size. For example, if the metal bit is only 2" long and you can only have 1" in front of the jig, then you will need a jig angle of around 35 degrees. But you will have to check the actual extensions possible for your blade.

If you dedicate the jig to the chisel, you can slot the thin jaw to hold the chisel at the desire angle. Usually this is not necessary, since wood seems to grip metal tools pretty well. You can make the jig without slots, adding them if the chisel slips.

Brent


http://www3.telus.net/BrentBeach/Sharpen/jigslant.