Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Millers Falls No 5 question

Posts

Millers Falls No 5 question

#1

Millers Falls No 5 question

Bill Tindal, E.TN

>This is my favorite drill but its chuck has a problem. The 3 thingies that grab the drill bit rattle around loose in the chuck housing. I would be most grateful if someone would provide a picture of what the insides of the chuck look like, specifically, what holds the 3 thingies together. This request is presuming that if I knew how it was supposed to be, I could fix it.

Re: Millers Falls No 5 question

#2

Not sure if this will help, but here you go *pics*

Dave Thompson

>Hi Bill, I haven't taken apart one of these heads. The crude tools I have won't budge them open, so here's an inside view from outside of a working MF#2. The MF#5 looks the same, but the smaller hole makes it harder to get light in there for a photo. I can certainly understand your desire to get it working again. I love these drills. They seem so underpriced on e-bay.

I haven't opened an MF chuck, though I have a vague recollection that a similar hand drill chuck had a ring spring that wraps around the bottom of the three teeth which pushes the teeth outward aginst the chuck housing. The teeth would just sit in the cut groove which you can see in the top photo.

good luck,

Dave




Re: Millers Falls No 5 question

#3

Re: Not sure if this will help, but here you go *p

Bill Tindal, E.TN

>Thanks for the PIC but it does not show what I need to see. The 3 jaw thingies have holes in them for some part that must be missing. It is not clear to me how any sort of spring would fit in these holes, but it must. Bottom line, I don't know what holds the 3 jaws together and pushs them to the outside of the housing.

Re: Millers Falls No 5 question

#4

Re: Millers Falls No 5 question

Warren in Lancaster, PA

>I have a different model Millers Falls, but the chuck looks to be the same as Dave's. In back of the jaw pieces is a piece shaped like a truncated cone. There are three wire springs attached to the backside of the cone that move in slots in the cone and are attached to the three jaw pieces. When the jaw is closed the three jaw pieces are held together by being pushed up into the front of the chuck and complete the cone shape with the truncated portion. When the the jaw is loosened, the springs move outward in the slots, pushing the jaws open. Each spring goes in a hole in the back of the cone, then loops around through the slots and into a small hole in the chuck piece, where it take a tiny right angle turn to hold it in place.

I would unscrew the chuck housing (you should see a joint near the back of the chuck) and gently pull the cone piece out so that if you have some good springs they don't fall out. Perhaps only one spring is missing and you can use another for a model.

Re: Millers Falls No 5 question

#5

Re: Millers Falls No 5 question

Bill Tindal, E.TN

>yes this is how my chuck looks and the springs are totally missing. I see th eholes, slots, etc you are refering to. Is the spring a single springy wire or a coil? A picture of what these springs look like would be helpful.

Re: Millers Falls No 5 question

#6

Re: Millers Falls No 5 question

Warren in Lancaster, PA

>I don't have the capacity to send a picture. The springs are shaped like a fish hook. If you plot the following points in millimeters (starting from inside the back of the cone) you will get a good picture of the spring. (0,0), (-5,1), (-5,5), (8,5), (8,8). Note that one angle is slightly obtuse, the others are right angles. The spring comes out the back of the cone, wraps around the back of the cone and into the slot, comes foreward into the back of the jaw piece and hooks outward inside the jaw piece

The springs are about .75 mm in diameter, somewhat smaller than a paper clip. The holes are rather larger than the springs so small paper clip material might work.

Re: Millers Falls No 5 question

#7

Re: Millers Falls No 5 question

Warren in Lancaster, PA

>The second and third points start with minus 5, not so noticable in the post.

Re: Millers Falls No 5 question

#8

Re: Millers Falls No 5 question

Bill Tindal, E.TN

>Thanks, I will see if I can fabricate the springs out of piano wire. It would be a delight to have this drill working properly.