Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Stanley 80/81 Blade Bevel Angle?

Posts

Stanley 80/81 Blade Bevel Angle?

#1

Stanley 80/81 Blade Bevel Angle?

Wiley Horne--So. Calif.

>Hi Folks,

Just received a new fun toy from Patrick Leach's last ebay run! A Stanley 81 scraper plane. I have a question for the galooterati....the previous owner prepared the blade with a bevel angle which looks to be in the 45- to 60-degree range. It's rounded over enough that I can't determine the original intention. Does anyone have an opinion from your own experience as to what bevel angle works well on an 81?

Wiley

Re: Stanley 80/81 Blade Bevel Angle?

#2

Re: Stanley 80/81 Blade Bevel Angle?

Derek Cohen (in Perth, Australia)

>Hi Wiley

Mine is honed at 45 degrees.

On a related topic, I wonder if anyone is making these in HSS or even A2?

Regards from Perth

Derek

Re: Stanley 80/81 Blade Bevel Angle?

#3

Re: Stanley 80/81 Blade Bevel Angle?

Wiley Horne--So. Calif.

>Thanks! 45 seems right. The closest I come on a hard blade is Veritas' carbide blade for their ball-joint floor scraper. It's only 2" wide, and am not sure it would be long enough to fit. Looks like maybe 3" long, but not stated:

http://www.leevalley.com/wood/page.aspx?c=2&cat=1,310&p=45784

Ron Hock makes high carbon 1/16" thick replacements for 80 and 81, which are different widths.

Wiley

Re: Stanley 80/81 Blade Bevel Angle?

#4

HSS?

Jim Reed @ Tallahassee

>Most scraper blades are high carbon and soft. The softness allows them to fold over without cracking. A2 that is annealed should work just fine. I cannot tell the difference between A2 and O1 when working. Hardened A2,however would probably crack before bending. I am guessing that HSS would just giggle if you tried to burnish it into a burr. A press and die might work to roll the edge, but would seem to be a little over the edge (no pun intended).

Re: Stanley 80/81 Blade Bevel Angle?

#5

I have a Hock iron in my 80...

Scott Burr in Ben Lomond, CA

>It came with a 45deg. bevel on it. I use mine just honed, no burr.

Re: Stanley 80/81 Blade Bevel Angle?

#6

Re: I have a Hock iron in my 80...

Wiley Horne--So. Calif.

>Thanks Scott, sounds like 45 is right, then. I'll try with and without burr.

Wiley

Re: Stanley 80/81 Blade Bevel Angle?

#7

Re: Stanley 80/81 Blade Bevel Angle?

Bart Leetch

>http://www.leevalley.com/wood/page.aspx?c=2&p=46266&cat=1,310 Here is the one I am waiting to arrive for my #80.

Re: Stanley 80/81 Blade Bevel Angle?

#8

You allow just one burr in the shop at a time?

Bill Houghton, Sebastopol, CA

>

Re: Stanley 80/81 Blade Bevel Angle?

#9

Re: Stanley 80/81 Blade Bevel Angle?

Jim Shaver - Oakville, Ontario

>Hi Wiley,

I have a Stanley 80 and I have been using a bevel angle of 45 degrees on it for years..I imagine that is very standard.

I have used it with and with out a burr, for me it works best with a burr.

Take care,

Jim

Re: Stanley 80/81 Blade Bevel Angle?

#10

Re: HSS?

Derek Cohen (in Perth, Australia)

>Jim

As you know, scraping creates a large amount of heat due to friction. This wears out a high carbon edge very quickly. I agree, trying to burnish a HSS blade into a hook would be some feat, but the #80 can be used very well without a hook. Further, there are big advantages in having as shallow a camber in the blade as possible - keeping it flatter means less camber at the cutting end, and this means less scolloping of the surface.

Regards from Perth

Derek

Re: Stanley 80/81 Blade Bevel Angle?

#11

Re: Stanley 80/81 Blade Bevel Angle?

Frank D. in Montreal

>One more vote for 45� with no burr.

Of course if Scott wants to come over for a beer, I'll certainly let him in.

Re: Stanley 80/81 Blade Bevel Angle?

#12

Re: HSS?

Jim Reed @ Tallahassee

>Actually, I use a LN112 with no burr. I never got into the scraper burr lore, but it seems to me that it might be difficult to get a consistent result along the edge. It is something that looks like it would take some practice. That is why I really like the 112. You may be really onto something with the #80 and HSS. Wonder how hard it is to find the steel stock?

Re: Stanley 80/81 Blade Bevel Angle?

#13

Re: HSS?

ThomD

>Though it's a different application, you can roll a burr in HSS turning tools no problem, usually I just grind it in, but either way works.

Re: Stanley 80/81 Blade Bevel Angle?

#14

Very funny Bill! 8^)

Scott Burr in Ben Lomond, CA

>

Re: Stanley 80/81 Blade Bevel Angle?

#15

WOW Thanks!

Scott Burr in Ben Lomond CA

>I've always wanted to see/ visit Montreal. If I ever get the chance I'd love to take you up on your offer!