Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

Vise Mounted Vise 1of 5

Posts

Vise Mounted Vise 1of 5

#1

Vise Mounted Vise 1of 5

Todd O. Cronkhite Maine Native, Presently Away

>Tho there is probably abit redundant to post these pics of my vise mounted shoulder vise I will anyhow. Tho no wheres near as nice as Jacks, it is still functional which was my goal.

First is a pic of the vise that this will go into. Probably a bit daft to show a pic of it, but it is part of this whole equasion, so I might as well eh?

Demensions:

The metal vise opens to just under 10" and is 4 3/4" deep

The Shoulder vise:

The front block is 7 3/8" x 4 3/4"

The Main Arm is 20 1/8" x 4 3/4"

The spacer blocks are 8 5/8" x 4 3/4"

The foot is 14 1/8 x 4 3/4" including the tail that goes into the groove in the spacer blocks. The groove is 1" deep and 1" wide.

With the shoulder vise in the metal vise it opens to a max of 2 3/8". If I need more I can put another block in the vise to gain a few more inches.

The only thing that is pretty much not self explainatory in the pics is that on the foot, behind that metal block in a cavity is a 3/4" nut that has been filed to round and than pinned to the threaded rod with a nail.

Really, the only construction tip worthy of note is this:

Before cotter pinning the "pusher" to the rod, ensure that the nut is not up against the metal block, but just short of touching. If it is touching the metal block it won't turn. when pinning the pusher to the rod, leave just a slight gap between it and the metal block.

hope all this helps, and makes sense. If any further info is needed let me know and I'll fix you right up.

Todd O.


img

Re: Vise Mounted Vise 1of 5

#2

Re: Vise Mounted Vise 2 of 5 

Todd O. Cronkhite Maine Native, Presently Away

>


img

Re: Vise Mounted Vise 1of 5

#3

Re: Vise Mounted Vise 3 of 5 

Todd O. Cronkhite Maine Native, Presently Away

>


img

Re: Vise Mounted Vise 1of 5

#4

Re: Vise Mounted Vise 4 of 5 

Todd O. Cronkhite Maine Native, Presently Away

>


img

Re: Vise Mounted Vise 1of 5

#5

Re: Vise Mounted Vise 5 of 5 

Todd O. Cronkhite Maine Native, Presently Away

>


img

Re: Vise Mounted Vise 1of 5

#6

Re: Vise Mounted Vise 5 of 5

Jim Shaver Oakville, Ont.

>Very Cool idea Todd,

I have thought of something similar, the surface area of your primary vise is important I would imaging for strength in the torque that the aux vise will apply to it under load.

Have you tried the second vise with a board clamped it to see the effect on the holding vise vise?

take care,

Jim

Re: Vise Mounted Vise 1of 5

#7

Re: Vise Mounted Vise 5 of 5

Todd O. Cronkhite Maine Native, Presently Away

>Have you tried the second vise with a board clamped it to see the effect on the holding vise vise?

Yup, sure have Jim. I vised up a board vertically and did some sawing, than vised it up horizontally and did some planing. Worked great.

T.O.

Re: Vise Mounted Vise 1of 5

#8

Re: Vise Mounted Vise

Derek Cohen (in Perth, Australia)

>Hi Todd

That is an excellent vise-in-a-vise. One of these days I shall have to revise my vise, or is that re-vise my vise?

I have plans to do the same as you. A couple of years ago I have tried spanning two face vises with a board:

Old file picture:



The past few years I have used an extension of that idea, where by I have a face vise that attached to the skirt:



It works well but I think I prefer your idea.

Regards from Perth

Derek

Re: Vise Mounted Vise 1of 5

#9

Re: Vise Mounted Vise 5 of 5

Kevin French

>I LIKE it T.O. and want one. I think I'll find in the dump next week.

Re: Vise Mounted Vise 1of 5

#10

Very clever!

Jim Reed @ tallahassee

>Glad to see you are putting your shop time to good use.

Re: Vise Mounted Vise 1of 5

#11

Thanks Jim, but.......

Todd O. Cronkhite Maine Native, Presently Away

>I wish to STRONGLY DISCOUNT any notions that this is my idea. somebody here the Island had posted a pic of it, and I just happened to like it enough to build a down and dirty version of it.

Proper credit for it goes to Jack, whom was a friend of BugBear's.

Thanks for the kind words none-the-less.

My latest trick is a Wagon Vise that rides on top of the benchtop. Bloody 'ell, I thought about building this vise into the bench top as I was building it, than talked my self out of it. than I see Tod Herrli using it inhis plane making video, and am now enamored with it. I'm really not to keen on te idea of chopping a slot into my bench top, so I am coming up with various ideas, one of which I have constructed and does work fairly well, but I think further developments would make it better. Sooooooooooooooo standby to see just what cobbled up contraption I come up with. I do have a good idea for the next attempt, and really it's quite simple, but I shall keep the cat in the bag until it proved to be a good worker.

I hate it when I disrequard that little voice in my head as just another crack-pot.

for those of you who have yet to visit Chis's blog, I think you're really missing out. I haven't spent much time on it yet myself, but it seems to be written in "real world" format. By this I mean; "his is what I did, and this is why what I did was stupid, so this is what I did to fix it, and this is why what I did to fix it was even stupider" ;~) Looks like it'll be good reading.

T.O.

Re: Vise Mounted Vise 1of 5

#12

Re: Thanks Jim, but.......Chris's blog???

George in Lowell Mich.

>

Re: Vise Mounted Vise 1of 5

#14

Re: I suspect it's...  *LINK*

Todd O. Cronkhite Maine Native, Presently Away

>


Chris's Blog

Re: Vise Mounted Vise 1of 5

#16

Re: Chris's Blog, try duece *LINK*

Pam Niedermayer - Austin, TX

>Todd, there are two, one for PWW and another for Woodworking Mag, both great, btw. And then there's Adam's A&M Blog, where there's a great entry on column orders.

Pam


Adam's A&M Blog

Re: Vise Mounted Vise 1of 5

#17

Thanks Pam

Todd O. Cronkhite Maine Native, Presently Away

>

Re: Vise Mounted Vise 1of 5

#18

Re: Vise Mounted Vise

Ernie Miller

>That looks an awfull lot like my vice I am going to have to make some of them wings for the bolt heads like yours I allways figured I would weld some washers to them to make wing nuts but not having a welder and the long wooden handles of yours will give them more torque.