Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

Effective cut angle and skewing planes

Posts

Effective cut angle and skewing planes

#1

Effective cut angle and skewing planes

Denis Ch�nard, Orl�ans, Ont.

>Can someone give me the formula to compute what the effective angle is when one planes while skewing the plane? For instance, a BD plane bedded at 45 degrees will give an effective cut angle of 30 degrees is the user skews the plane at 45 degrees (at least that's what I've read).

Brain is stuck in 1st gear this morning, can't come up with the formula...

Thnx,

DC

Re: Effective cut angle and skewing planes

#2

o.t. but related ...While you are at it...

vlparisian in warm and pleasant Houston

>how do I compute the angle for miter joints for tapered pieces. Background: Thought I would make up a waste basket for SWMBO. 16 sides is 11.25 degrees but then I taper the sides in at about 5 degrees on each side. I did a dry run on scrap wood that was close, but had gaps on the inside of each joint when I taped it togeter with blue masking tape.

Now what? I know I'll likely kill some electrons setting this up.

Victor in Houston - celebrating some Chamber of Commerce weather here today

Re: Effective cut angle and skewing planes

#3

Re: Effective cut angle and skewing planes

Donald Pierson

>Denis,

I have seen the statements about effective cut angle and I am not clear about what that means. However if the plane is skewed, maybe the cosine of the angle is the formula you are looking for. A 2 inch iron skewed at 45 degree will plane 2*cos(45)=2*0.707�= 1.414� wide swath. Also 45*cos(45)=31. It has a lot to do with the fact the planed swath is narrower the greater the skew angle. I have a hunch there is an effect involving changing from static friction to dynamic friction but that is beyond my interest.

Re: Effective cut angle and skewing planes

#4

Re: Effective cut angle and skewing planes

Warren in Lancaster, PA

>If x=bedding angle

y=skew angle

z=effective angle

Then tan z =(tan x)(cos y)

and z=arctan {(tan x)(cos y))

Arctan means inverse tangent or "the angle whose tangent is". In other words, multiply the tangent of the bedding angle times the cosine of the skew angle and find what angle has this number for a tangent. In the case of a bedding angle of 45, tan45=1 so

z=arctan(cos y}

Re: Effective cut angle and skewing planes

#5

Re: Effective cut angle and skewing planes

vlparisian - Houston

>Will this work for my little puzzler that I tagged on too?

Victor

Re: Effective cut angle and skewing planes

#6

Re: Effective cut angle and skewing planes

Warren in Lancaster, PA

>My ride to Williamsburg is due in 5 minutes, so I don't have much time to think about it. Definitely the same problem, but have to think it out. My quick hunch is that 79 degrees, thats 90 minus 11, is the "effective angle" and you are looking for the "bedding angle" of the similar problem.

Re: Effective cut angle and skewing planes

#7

Polycut

Ed Mulligan, Cape Cod

>As Warren says,his formula will give you the bevel angle for your project. You also need the miter angle. For your project the formula is miter angle = arcsin(sin 11.25 x sin 5) which = approximately 1 degree (or 89 depending on how your miter scale reads).

John McGaw wrote nifty bit of software which does all the work for you. Look in the BP Articles link on the left under downloads and find the 'Polygon Angle Program'.

Ed

Re: Effective cut angle and skewing planes

#8

Thanks, BP it is...

vlparisian in warm and pleasant Houston

>