Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Pooched it again! (OT)

Posts

Pooched it again! (OT)

#1

Pooched it again! (OT)

Gerry D.

>Rehabbing the first floor powder room for SWMBO's annual Christmas boarding house. Pulled everything out. Walls were a mess. Skim coated, and painted. Installed new baseboard and quarter-round. (Quite proud of self, coped joints that fit like a jig saw puzzle. Work done with coping saw, rasps, miter box.) Installed new commode.

Now here's the rub. The first vanity that the lady of the manor picked had drawer's at 21", the same height as the water lines. Picked up a different vanity. The back of the new vanity runs in a straight line from the top to the floor. The baseboard and quarter-round keep the vanity approx 1 to 1 1/2" from the wall. The vanity and back splash have to be flush. The vanity is open, with 4 post legs.

Appears that I now have to notch the trim work I was so proud of. Any possible suggestions as to how to proceed from this esteemed collection of galoots? I would really hate to have to pull all the trim out. Any methods for notching it in place. Willing to use electron burning devices to achieve ends. (mea culpa, mea culpa)

Thanks,

Gerry

In violation of the 7 P's (proper prior planning prevents piss poor performance)

Re: Pooched it again! (OT)

#2

Re: Pooched it again! (OT)

woodburnbob

>I'm not sure I can visualize this. Are you saying the back surface of the two back legs of the vanity need to be flush with the wall and your molding prevents it? Wouldn't you just cope the legs and not the molding? A picture of the vanity would help a lot.

Re: Pooched it again! (OT)

#3

Re: Pooched it again! (OT)

Paul in NJ

>How about scribing - coping the back posts to the trim? The coping cuts to the trim will not be very visible since they are on the back side of the posts.

Paul Dzioba

Re: Pooched it again! (OT)

#4

Unless...

woodburnbob

>your vanity is porcelain like this one, I suppose.


I'd probably add a 1/2" or so jigsawed "gasket" of my favorite wood between the deck and the wall.

Re: Pooched it again! (OT)

#5

Re: Pooched it again! (OT)

Gerry D.

>Sorry, I didn't provide enough info. The first 3" of the legs are metal. (The vanity is store bought) The back of the vanity, including the legs, form a straight vertical line. As such, the base board and quarter-round keep the vanity away from the wall. It appears that I'll have to notch the baseboard to fit the vanity (similair to a built in), but I'm not looking forward to pulling out the trim I just put in. Also because the joints are coped, I would have to remove the trim from two of the walls.

Re: Pooched it again! (OT)

#6

Re: Pooched it again! (OT)

Bill Houghton, wintry rain again, Sebastopol, CA

>This, of course, is why they always say, "Buy the XXX before you begin work, so you'll be sure it fits" - more easily said than done in real weekend warrior life, of course.

Would it work to put in some kind of trim piece that fills the gap with the vanity out from the wall? Do we have a Design Feature (or, as my computer-geek friends, describe it, an Undocumented Feature) lurking here?

Re: Pooched it again! (OT)

#7

Re: Pooched it again! (OT)

thomd

>I have done that kind of thing. Like once I put a trim around a window that reached from the floor up, rather than put the skirting, and blow out the paint, I cut the boards with a chisel. Just use a realy sharp chisel, start cutting a fraction outside the layout lines as though chopping a large dovetail socket.The clean back to the lines.

Re: Pooched it again! (OT)

#8

Jack Guzman from Maine

Re: Pooched it again! (OT)

Jack Guzman from Maine

>Assuming I understand you correctly,I would scribe the base and quarter round with the vanity pushed back as far as it will go using the sides of the legs as a guide.Then cut the scribed lines with a knife as deeply as possible.Cut the majority out with a small backsaw. Anything the saw can't reach,cut with a chisel.Sharp tools make this job easier.---Jack

Re: Pooched it again! (OT)

#9

Cut off rear legs?

Ed Mulligan, Cape Cod

>Can you strengthen the vanity back and bolt through it into studs? End of structural reason for rear legs.

Ed

Re: Pooched it again! (OT)

#10

Re: Pooched it again! (OT)

Frank D. in Montreal

>I can do this kind of thing very easily with my Fein Multimaster (cleaning up with a paring chisel if necessary), but on this board I'd suggest a chisel and saw as others have.

Re: Pooched it again! (OT)

#11

Re: Pooched it again! (OT)

John in Kerrville

>Frank D. has the right idea.