Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Planing while tired, or Ain't that pathetic.

Posts

Planing while tired, or Ain't that pathetic.

#1

Planing while tired, or Ain't that pathetic.

Gerry D.


>Still working on the bench. Without a power jointer or planer, limited to the upper body workout. After getting the kids down, head out to the garage. Slap a 8'6" X 4 1/4" X 1 1/4" down on the temp bench. Hit the high spots with the jack. Run lengthwise with the 7. Check. So far, so good. Not to shabby for an amateur.

Flip the board. Hit the high spots with the jack. Hmm, a little more tear out. Grab the 7. What the hell? Digging in like a son of a gun. Back off the blade. Run her down, not cutting, not cutting, rip. Big arsed tear out, damn near a divot. Try again, same thing. Check plane. Not jammed. Disassemble. Everything looks OK. Reassemble. Run her again, same problem. Board is beginning to look pretty shabby.

Disassemble 7 again. I've never had a problem with this one before. This is pop/fir, should be no problem. Check blade, seems OK. Maybe it needs a touch. Hit the stones, 45 minutes later (You don't want to ask about me and sharpening) reassemble. Hit the board again. @#$%$%%!!!! Blue streaks fill the air, birds dropping out of the sky, neighborhood raccoons traumatized, etc.

OK, sit down, this ain't rocket science. Grab a smoke. Think basics, basics. Back to bench, look at board. LOOK AT GRAIN ON BOARD. Refer to self as mental midget. Flip board so grain rises toward planing stop. Hit it with 7. All is good with the world.

Re: Planing while tired, or Ain't that pathetic.

#2

Re: grain direction

paul womack


>related tip; when you finish planing each beam you're planning to use for your glued up top (I'm making an assumption here), mark the grain direction on both (upper and lower) faces, in chalk or something similar.

When you're deciding your board assembly for the glueup, you need to juggle many factors:

* heartwood up/down (cupping)

* pretty face up

* good grain matching at joints

* all grain directions the same way on upper surface

That last one is really important if you're planning to plane your bench flat - otherwise you'll have a borderline unplaneable top.

In the midst of juggling all those other factors, some nice guiding chalk arrows are helpful - not neccessary, but then it's not neccessary to "mark the waste" when cutting dovetails. But it's helpful, and avoids mistakes.

BugBear

Re: Planing while tired, or Ain't that pathetic.

#3

Re: grain direction

Greg Sloop, Portland Oregon


>Alternatively, if you already have the top glued up, or can't run the grain all the same direction...DAMHIKT...

A toothed blade will help remove a lot of material without too much tear-out. Then you can use a higher cut angle for the finish passes that may not produce the same amount of tear-out. (I'm not sure what wood you're using, but this often helps even "against" the grain on hard-woods.)

It's not a perfect solution, but it might help if required.

-Greg

Re: Planing while tired, or Ain't that pathetic.

#4

Perhaps if I read more carefully... :)

Greg Sloop, Portland Oregon


>I see it's softwood. I doubt a higher angle will make a lot of difference here. A toothed blade might though.

BugBear's thoughts however are the best - doing it right up front if possible will make life a lot easier later...

Cheers,

Greg

Re: Planing while tired, or Ain't that pathetic.

#5

Re: grain direction

Gerry D.


>Paul,

Thanks. Most of your points had already been considered, except for the heartwood issue. Hadn't thought of that from a cupping stand point, but due to the aesthetics, I believe it would have resolved itself, i.e pretty wood on top. I'm attempting Chris Schwartz take on the Roubo bench and finding that hand dimensioning this much construction grade lumbar is a healthy work out. I do admit to cheating and using the TS to rip to general size. My masochism doe have limits.

Last night's fiasco, which involved over two hours of fussing, fiddling and cussing, was the result a long day and not focusing on the basics. Time wasted adjusting a tool, when the user needed the adjustment. Will consider it a lesson learned.

Gerry

Re: Planing while tired, or Ain't that pathetic.

#6

Re: Planing while tired, or Ain't that pathetic.

Todd O. Cronkhite Maine Native, Presently Away


>Gerry,

Doing anything except sleeping while tired is usually not a good idea, but Pathetic, no, you're being a bit harsh on yourself. Pathetic would be putting the kids down and than going to some bar for several hours.

What's worse a little tearout or a DUI/killingsomebody/going to jail? I'll take the tearout thank-you. In the grand scheme of things, even in a benchtop, a little tearout isn't all that bad. Remember Todd H's axiom about being a "Machine Man"?

T.O.

Re: Planing while tired, or Ain't that pathetic.

#7

Re: heartwood/cupping

paul womack


>it's a common practice to alternative the heartwood up/down between adjacent pieces in a glue up; so that any tendancy to cup in the induividual pieces causes a ripple instead of a cumulative cup.

I'm sure I saw a diagram somewhere, but can't find it right now.

BugBear