Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

I'm slidinging over to the dark Side - Long

Posts

I'm slidinging over to the dark Side - Long

#1

Bart Goldberg

I'm slidinging over to the dark Side - Long

Bart Goldberg


>Hi hand tool folks,

In my pure frustration with not having large enough machines to mill large stock, I'm reconsidering my options and decided its time to learn to use some of the hand planes I'm accumulated over the years and put them to real use.

Current project requires me to flatten some large chucks of walnut I picked up from my sawyer. 18" wide, 6 ft long, and 2 inches thick. These boards are to large to face joint on my Delta DJ-20 8" joiner, and to large to plane on my Dewalt 12" planer.

Since I don't have access to larger machines, and I have neither the cash or space for larger machines, I need to learn to hand plane this board flat.

Here's my inventory:

1) Low Angle Jack

2) 4 1/2 Smooth plane

3) Adjustable Mouth Block

4) Chisel Plane (great for removing glue)

5) 2 different size shoulder planes (for cleaning up tenons)

I started out using the low angle jack going at near right angle across the board. The board is cupped on one side and High on the other. I figured I could keep planing till I could hit both edges of the board. The low angle jack seemed to work fairly well at flatting from side to side, but not to good for the length of the board.

I'm assuming I will need to get either a fore plane or a Jointer plane to do that (or both).

Questions:

1) Does one usually flatten side to side, then along the length of a board?

2) What's the best picks of hand planes for this flattening exercise.

What I don't have yet, I will start to shop for.

Thanks

Bart

Re: I'm slidinging over to the dark Side - Long

#2

Re: I'm slidinging over to the dark Side - Long

Thom D


>There isn't so much a particular right way as you just put time on task on any areas you don't want. Like you, I like working across the grain about 45 degree, and I use a curved blade. With that combo you can take very heavy shavings, and you need a large mouth opening. I prefer a wooden Jack plane, of whatever design, for it's light weight and slipery sole to do the initial butchery, or a scrub plane. You can get a board as flat as any planer without the use of a fore or jointe plane but they may make things easier. A metal jointer can weigh 7-9 pounds so I normally use it only for tunning joint fit.

If you have a lot to remove. tools like axes and adzes can speed initial wasting, as can a chainsaw, which does a pretty good job as a planer.

Re: I'm slidinging over to the dark Side - Long

#3

Re: I'm slidinging over to the dark Side - Long

Jerry Nicholson


>If the cup is really bad and you have a lot of material to remove, you might save time with a scrub plane. Good choices are an old Stanley #40, an old wood scrub plane, or a bright shiny new Lee Valley scrub plane. I have found that it takes quite a lot of work to get the blade ground and sharpened to an acceptable radius on the old planes - they are usually pretty badly messed up. The LV at $129 in my new LV catalog would come with a thick blade already ground to the proper radius. I don't have one of these but it would sure look nice next to my bevel up smoother and low angle jack plane :)

Jerry

Re: I'm slidinging over to the dark Side - Long

#4

Re: I'm slidinging over to the dark Side - Long

Dave Thompson


>You can probably get more than 95% of the work done with just your jack plane. I typically plane at a 45 degree angle to the grain. Be concious about not rounding over the edges. Initially, you may end up flipping the warped board a few times just to level out one side enough to sit on the bench. If you want two parallel surfaces, once you get one side flat, flip it over and then scribe a parallel line so you can see the target. On walnut, you'll probably want to use chalk or white pencil. Better yet, you can snap a chalk line if you have one. You can get the surface visibly flat with just your jack plane.

Be patient. Think about how good this exercise is for you, and how much hand planing experience you're gaining, and imagine how much money and space you're saving by not having to buy a 20" power jointer and 20" planer, not to mention a large enough dust collector. What doesn't kill you makes you stronger ;-)

Re: I'm slidinging over to the dark Side - Long

#5

Re: I'm slidinging over to the dark Side - Long

Paul Kierstead


>1) Yup, normally. Well, 45 across one way, 45 the other way, then the length, with lots of identifying the real nasty bits and localizing some work to those.

2) Jack for the rough work, jointer for the final tuning.

And, for an answer you didn't ask for: I hope you are in good shape, and/or that board isn't too far out of flat. It is a tremendous amount of work on a board that size, especially if you need both sizes parallel to each other. And, if you haven't done it much, it is pretty tricky as well (although not *too* bad if there is no twist). Good luck! You'll be fitter for it :)

Re: I'm slidinging over to the dark Side - Long

#6

Oh, and ...

Paul Kierstead


>If the final size is not 6' long, save yourself a lot of work and saw the board down. It is much much less work to flatten two 3' boards then to flatten one 6' board (assuming the 3' came from the 6' of course...)

Re: I'm slidinging over to the dark Side - Long

#7

A heretic option

Denis Ch�nard, Orl�ans, Ont.


>I don't know if that'a an option for you, but you could always rip the board in two and run each part through your machines, then re-glue the two parts together. This way you can use your current machines.

If you remove little wood (rip with a bandsaw instead of the tablesaw) the glue joint shouldn't be visible much.

DC

Re: I'm slidinging over to the dark Side - Long

#8

What are you building?

jimreed@tallahassee


>This wood seems too nice to be learning on. Maybe you could take it to a mill where their big machines would gnaw it into submission in about a minute. While there you could pick up some inexpensive maple to learn on. What are you going to make? That 18" wide walnut makes me drool.

Re: I'm slidinging over to the dark Side - Long

#9

Re: What are you building?

Bart in Flemington


>Well, I have several really nice chucks of walnut from my local sawyer. At the moment, I'm getting ready to build a mantle for a fireplace as a gift for my brother. After that, I was thinking of making some kind free form coffee table. Here is a peek at my first piece all cleaned up with a coat of waterlox on it.


img

Re: I'm slidinging over to the dark Side - Long

#10

WOW!

jim reed @ tallahassee


>...speechless...cannot talk...

Re: I'm slidinging over to the dark Side - Long

#11

3 rd option...

Edward in Vancouver


>Nah, you don't need any new machinery, don't even need a really nice peacefull and satisfying Saturday morning workout with handtools. Nope, what you need to do is pack up that nice stuff and ship it out here, I'd be happy to take some of that lovely walnut off your hands....