Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

How to Tweak a DT Saw?

Posts

How to Tweak a DT Saw?

#1

How to Tweak a DT Saw?

Tony - Memphis


>I bought a 20tpi Crown dovetail backsaw. It has a huge amount of set! What is the best way to start to rectify this? Can I just file it off, or do I have to bend them back, or what. it should be obvious that I have never done this before! I have an LN DT saw, but I wanted a 20tpi and thought it might be fun to buy something inexpensive and tweak it. I plan on making a new handle too. Thanks for the help.

Tony

Re: How to Tweak a DT Saw?

#2

My 2 cents.

Vlad


>Tony,

Why do you want to remove the set? How much set is it? If it's blowing out the fibres on the back of the piece you are cutting then it's too much - according to Kirby. That's fine if that part of the DT is going to be exposed. If not it doesn't matter

If you need to take set off, I put the piece of a flat table and put a piece of hardwood on top - maple - and hammered it out by lightly tapping it along it's length. After that you'll have to test the saw to see if it tracks straight and amount of set that you want. I think that's a lot of trouble for something insignificant. Personally, I'd just use the saw and when it's dull then sharpen/set it to the specs you want.

I have a Freud with 20 tpi and lots more set than the saws I used to make and it cuts fine. I think there is far too much attention to "set". I would be worried about too little rather than too much (but not excessive of course).

Good luck.

Best.

Vlad

Re: How to Tweak a DT Saw?

#3

Re: How to Tweak a DT Saw?

Derek Cohen (in Perth, Australia)


>Hi Tony

I have a Crown gents saw. I think it is 17 tpi rip. It did require just a smidgeon off the set on one side (it was pulling to this side), and now it cuts very sweetly. To do this I simply ran the one side once on a diamond stone, then tried it out before taking off any more set. I think I only had to run it twice this way in all.

In my opinion you have more control when stoning the set than when hammering/bending it.

Regards from Perth

Derek

Re: How to Tweak a DT Saw?

#4

Re: My 2 cents.

Tony - Memphis


>I can't recall for sure, but I think it was around 0.009" on each side. When I cut, I can move the saw side to side quite a bit. I really think it is too much.

Thanks,

Tony

Re: How to Tweak a DT Saw?

#5

STW

david.marcus.brown


>Do you see yourself making saws again Vlad?

Re: How to Tweak a DT Saw?

#6

stoned saw better than hammered...!

david charlesworth


>Agree with Derek, fine slipstone partly sharpens the tips of the teeth instead of blunting them.

Rob Cosman drags his blade over a diamond stone, using thumb pressure, I move a slipstone along supported blade from heel to toe.

Careful not to remove too much, testing the saw frequently is wise.

Set of about 3 thou" on each side is nice, but expect all craftspersons have their own preference.

best wishes,

David Charlesworth

Re: How to Tweak a DT Saw?

#7

Re: stoned saw better than hammered...!

Joe Rogers, Northern Virginia


>I would think that a stoned set saw would have a much smoother kerf than a saw with just "set" teeth. This process would ,of course, remove...no... even out any rogue highly set teeth that will rasp the kerf while in use. This is an improvement in preparing saw teeth in my opinion. Hand cutting and sharpening teeth with the inherent random spacing is also an advantage. This quality improves the smoothness of the cut. Random spacing and consistent set, I want both.:-)JR

Re: How to Tweak a DT Saw?

#8

Re: STW

Vlad


>Not really. I'm enjoying my kids, golf and day job far too much to be doing repetetive tasks like sawmaking. I'm sure an urge will hit me to make something different but not right now.

Cheers.

V.