Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

Do I need a vapor barrier?

Posts

Do I need a vapor barrier?

#1

Do I need a vapor barrier?

Todd O. Cronkhite Maine Native now in Jax Fl.


>OK, so I finally covered my shop, which in concrete, floor with plywood, and now the thought occurs to me--do I need to put a sheet of plastic, ot thin styrofoam sheeting as a vapor barrier between it and the floor? I've never had a moisture problem with it before, but than again, I've never had it covered with plywood before either. Yes, this question to come to me while I was in the shower--as usual.

Todd O.

Re: Do I need a vapor barrier?

#2

Re: Do I need a vapor barrier?

Bob Hutchins in central TX


>Howdy Todd!

Did you just lay plywood on the floor or did you put down some 2x4's first? If you just placed the plywood on the concrete, I'd say you are in for some moisture problems.

Several years ago, I was reading up on putting plywood on the shop floor over the concrete slab to make it easier on my legs and back. I can't remember where I read the article (I'd cite it if I could), but the author recommended laying poly down, overlapping it by a foot or so and taping it. He also recommended lapping the poly up the sides of the walls above the level of the new floor. His premise was that concrete will wick moisture from the soil and the underside of the plywood will cause it to condense instead of evaporating. He put 2x4's laid on the wide face on 24" centers and used 3/4" T&G treated plywood. IIRC, he also placed extra 2x4's to support the plywood under his heavy power tools and under his workbench.

I don't know where the author was living or if that would make a difference. Perhaps colder climes with moderate rainfall -- say Pennsylvania -- are worse than warmer climes with less rainfall -- say Texas. With Florida's relatively high average annual rainfall, I'd say you will have more moisture than I will; and I'd guess you will have more condensation there, too.

HTH

BobH, who is NOT in the shower.

Re: Do I need a vapor barrier?

#3

Re: Do I need a vapor barrier?

Todd O. Cronkhite Maine Native now in Jax Fl.


>Bob,

the plywood is straight on the floor. Fiqured I'd start out as simple as I could than improve it as required. I've painted it white with some left over Kilz that I had kicking around. Today was my first day on it, and tho I didn't spend much time on it I do think that it has made a difference. I think it would hurt nothing if I laid some of that thin sheet styrofoam under it. Better have it and not need it, than to need it and not have it I guess. I hare for rot to set in which would attract insects. ARRRRRRRRRRRRRRRRRRRRRRGH!

Took me right at two hours just to get my workbench jacked up on two 1.5 ton floor jacks, moved, than rolled up onto the plywood. I'm in no hurry to do that again, but what's gotta be done gotta be done eh.

T.O.

Re: Do I need a vapor barrier?

#4

Re: Do I need a vapor barrier?

Neal in San Jose


>You probably do. Before you pull all the plywood out, pull out one piece of ply and tape down a large piece of plastic sheet for 24 - 48 hours. See how much moisture collects on the bottom of the plastic. I'm guessing you'll see enough moisture to convince yourself that you have created a problem. The paint you put on the ply will make the issue even worse! HTH Neal

Re: Do I need a vapor barrier?

#5

I'll second that approach.

V Parisian


>That's a pretty straight forward test and it will make a believer of you. The paint over the plywood will trap moister also. The paint will blister and start to flake off at best, or your plywood will just rot and attract unwanted insects and/or mold.

Victor - in beautiful sunny Houston.