Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

$10 Chute Board and Plane

Posts

$10 Chute Board and Plane

#1

$10 Chute Board and Plane

Paul in NJ

>I was perusing through my reprint of the 1909 Edward Preston Catalog by Astragal Press the other day and noticed they were offering wooden 'Shuteing Planes'. They were the size of a trying plane (22 inches) and had a handle on the side instead of the top. I had an extra wooden jack plane and decided I would experiment with it. The handle was cracked off and clumsily attached with a screw and had some checks in the end but nothing terminal. To the plus side the blade and wedge were in good shape and also the abutments and cheeks were solid. It also was made not to use a chip breaker which I subsequently did not have to clean or tune.

This jack plane was made by the Ogontz Tool Co., a brand name used by Sandusky. Companies like Auburn, Chapin, Ohio, and Sandusky built an enormous amount of planes each year. At their peak some of these companies were making more than 50,000 planes a year. These bench planes are very common and I see them everywhere at flea markets, ebay, and antique stores for very reasonable prices. My point is I don't feel bad modifying a very common wooden plane that has seen a hard life. If you are worried about destroying a valuable plane check the makers stamp on the toe of the plane. Pollak's 'A Guide to the Makers of American Wooden Planes' is an excellent resource. You could also ask here and I am sure you would get a quick answer.

I lightly jointed the sole and right side of the plane to square them to each other. I was careful not to remove too much from the side so I would not weaken the thin area of the cheek. It didn't matter if I removed a little more from the sole which is normal maintenance for a wooden plane anyway. A wider mouth was no concern since it would be used to plane end grain. The handle came from a scrap of cherry; cut, rasped, and filed to a comfortable shape and simply attached with a little glue and two screws. I then ground off the camber on the blade, ground a new bevel, and proceeded to flatten and sharpen the blade. All of this took about three hours with the blade probably taking the most time. The chute board was made from leftover plywood and a little maple. They are pretty simple to make but you need to take care aligning the fence. There are plans for them all over the web. I waxed my plane and runner on the chute board and adjusted the blade for a light cut. It took nice shavings and was very comfortable to use.

This is a nice little project done on a rainy day that won't take too long and it won't break the bank. If I were to do it over I probably would use a try plane for a little more heft but I am happy with how this one worked out.

Paul Dzioba


img

Re: $10 Chute Board and Plane

#2

@nd Picture 

Paul in NJ

>


img

Re: $10 Chute Board and Plane

#3

Interesting set-up...

Scott Burr in Ben Lomond, CA

>Looks like you made a nice shooter Paul. Is it comfy to hold with the handle placed where it is? Also I noticed the handle not rounded on the front face. Do you just palm it so to speak?

Re: $10 Chute Board and Plane

#4

Grip

Paul in NJ

>The handle fits in the web between the thumb and index finger. The rest of the fingers curl down against the wedge. It is very comfy, no sharp edges touch your hand.

Paul Dzioba


img

Re: $10 Chute Board and Plane

#5

Re: Interesting set-up...

Todd O. Cronkhite Maine Native now in Jax Fl.

>Paul,

Very nice job. I see no harm in giving an otherwise abused plane a new role in Life. Actually I perfer that to seeing it left in a neglected and unused tool. Good Show.

I'd also be interested in seeing your shoot board as well.

I also must confess to thinking the handle looks, well shall I just say a bit different, and wonder why you didn't go with the more traditional tote as we know it. Now, this is not to knock your handle as it looks very well made and quite nice. Action shots forthcoming?

Todd O.

Re: $10 Chute Board and Plane

#6

Re: Grip

Todd O. Cronkhite Maine Native now in Jax Fl.

>Any problems with your fingers restricting the ejection of shavings?

I can see where the handle placement would be conducive to getting a good solid cut as it is placed just above the cutter. Good thinking thinks I.

T.O.

Re: $10 Chute Board and Plane

#7

Re: Interesting set-up...

Paul in NJ

>This is the traditional handle for this plane. If you look closely at the Preston catalog page behind the plane in the first picture you will see it is the same. The advantage of this handle is that it gives you a lower center of gravity. The fingers don't seem to impede the ejection of the chips, they are a little further back on the wedge. The chute board is nothing special. It is really just a bench hook with an extra piece of wood for the plane to slide on.

Paul Dzioba

Re: $10 Chute Board and Plane

#8

Re: Interesting set-up...

Todd O. Cronkhite Maine Native now in Jax Fl.

>Ahhhhhhh yes, I see it now Paul. Very nice job of re-creation.

T.O.

Re: $10 Chute Board and Plane

#9

Had a feeling that's how it worked. Thanks!

Scott Burr in Ben Lomond, CA

>

Re: $10 Chute Board and Plane

#10

Nice!

Bill Houghton, finally Spring? in Sebastopol, CA

>and if you were a southpaw, you could just as easily have made it lefthanded. Very clever.

Re: $10 Chute Board and Plane

#11

Re: $10 Chute Board and Plane

Dan Clermont in Burnaby

>Nice job Paul.

That plane looks like a shark ;)

I like it!

Cheers

Dan C

Re: $10 Chute Board and Plane

#12

Re: $10 Chute Board and Plane

David C

>I am new to the chuteing board and have a question. I bought a Lie Nielsen no. 8 to use as a jointer and on a chuteing board. How do you keep the blade of the plane from cutting the edge of the chuteing board? You have to have a straight line between the ends of the board to get a straight cut. Do you cut away the portion where the cutter will work?

Re: $10 Chute Board and Plane

#13

You got it David

Todd O. Cronkhite Maine Native now in Jax Fl.

>When you use it for the first time you will remove a few shavings from your strip, than no more.

Yes, a straight strip is essential for a straight cut as that is what is guiding your plane.

Todd O.

Re: $10 Chute Board and Plane

#14

What ToddO said and...

Ted Owen, Pittsburgh

>because the plane blade does not extend across the entire width of the sole, part of the strip will survive. After the first few swipes remove strip where the blade reaches, the #8 will bottom out. Thereafter, only the workpiece, not the shooting board, will feel the blade.

If you later extend the blade farther, it will temporarily cut into the shooting board strip a bit.

I think you'll love using a shooting board.

Best, Ted

Re: $10 Chute Board and Plane

#15

Re: Southpaws and Wooden Planes

William Duffield, on the Cohansey

>As you are probably aware, I too am a southpaw. Unlike some other, trickier woodworking operations, using a chuteboard plane, or for that matter a plough plane, can be done with facility either handed. The chuteboard I use is right handed, and I don't have a problem with it, or with the Bailey and Bedrock planes I use with it. Also, today, I tried out both of Paul's new plane creations. They both work surperbly and comfortably right handed. (Well, there was a minor problem with the depth stop on the plough, but a minute or two with a file, and Paul will fix that.) At first, comparing the plough to the metal combo planes I'm more familiar with, I was surprised that I didn't seem to miss the knob on top of the fence or on the front of the body. Then I realized that it was more important to apply lateral pressure to the side of the fence with the left hand than to have a comfortable place to park it that was much too high to effectively keep the plane normal to the groove being created.

With a chuteboard plane, keeping the hand as low as possible is also important to keep you from twisting the plane out of the chute when you encounter a difficult spot. A high knob on top can have a tendency to do this, but not the older woodie designs, like Paul's.