Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

recreating 18 century moldings

Posts

recreating 18 century moldings

#1

recreating 18 century moldings

bill tindall

>Until recently I presumed moldings on old furniture, as well as the pyramids and the rings in Peru, were made by aliens using advanced technology, reasoning that the technology of the time could not accomplish these tasks. Well, I have been fretting over how to make ogees for this chest I am building. At wits end I had at it using what I had at hand. I nibbled away what I could with a table saw blade and sculpted the remainder with the tools shown. I found it easiest to make the scraper and use it to scribe the profile. Lots easier making the piece fit the scraper than the scraper fit the piece. The stick is actually 2 pieces of molding that will be sawed apart for a part of the assemblies of molding at the case top. I guess the bottom ogee will get made similarly as I have not come up with anything quicker. It actually took about 10X less time than the time I have spent fretting.


img

Re: recreating 18 century moldings

#2

Dang they were smart, weren't they?

Bill Houghton, sunny today yahoo in Sebastopol, CA

>It is amazing to find out how much we can do with how little.

Re: recreating 18 century moldings

#3

Re: recreating 18 century moldings

paul womack

>Were you hand holding the scrapers, or using them in a holder ("stock")?

Nice result in either case.

BugBear

Re: recreating 18 century moldings

#4

York pitch?

jim reed @ tallahassee

>Looks like a piece of walnut (?) and also a York pitch plane (?). I have a set of York pitch H&Rs and find them the bees knees for working mouldings in hardwood. Kinda a cross between shaving and scraping. Your moulding looks great, by the way.

Re: recreating 18 century moldings

#5

Details?

Wiley Horne

>Bill,

Beautiful result! I'm visualizing that maybe you marked the profile with a Sanford sharpie, and then machine ground some metal away, and then hand filed to the line. Or some such. But what did you really do? Also, is the metal hardened or no? Did you hone the edge--or just use the edge off the file?

Wiley

Re: recreating 18 century moldings

#6

Re: recreating 18 century moldings

Paul Kierstead

>It actually took about 10X less time than the time I have spent fretting.

This was, and remains, one of my hardest lessons in woodworking. So many times I have fretted and fretted and then finally got disgusted, gone down and grabbed some tools and it came out fine. Sure, once in a while it fails miserably, but y'know, I can try again and it *still* takes less time. Amazing stuff, isn't it? Just do it!

BTW, great looking moulding.

Re: recreating 18 century moldings

#7

Re: recreating 18 century moldings

Warren in Lancaster, PA

>Nice job, Bill. I think it will only get easier with experience. I have a neighbor who runs a molding machine almost full time. He can make moldings for as little as 15 cents a foot, but don't ask for just 100 feet. For small custom moldings the hand methods are best.

Re: recreating 18 century moldings

#8

Hi Warren, just sent you some email on this topic

Dave Thompson

>

Re: recreating 18 century moldings

#9

scraper answers

bill tindall

>Using circle template shown in pic I scribed profile on hardened scraper stock or lumber banding material(the small pieces). Roughed out pattern with 1/4" grinding wheel, note burn marks on steel where it didn't matter. Filed to line with needle files. Couldn't figure out how to refine scraper inside curve edges any further so used as is.