WoodCentral Forums

Est. 1998 — 27 years of woodworking knowledge

Hand Crank Grinder Conversion

Posts

Hand Crank Grinder Conversion

#1

Hand Crank Grinder Conversion

Todd O. Cronkhite Maine Native now in Jax Fl.

>Here is a picture of one of my hand crank grinders that I have built as portable base for as well as a sliding tool rest. The rest only sides back and forth and not up and down to help compensate for the wheel wearing down. This really hasn't been a problem up to this point, but still is something that needs to be considered. The tool rest is wide enough so that most chisels and plane blades will pass completely from one side to the other thus being able to make a complete pass. This base allows me to use it most anywhere instead of relying on a bench edge. The problem with most of these grinders is that the clamping screw is not deep enough to clamp to my 3" thick benchtop anyhow. Now I can positon it any way I want and clamp it down with either a holdfast or a small clamp if close to the edge.

Todd O.


img

Re: Hand Crank Grinder Conversion

#2

Re: Hand Crank Grinder Conversion

Patrick Gibbons, Houston, TX

>Todd, that's better living through Neander thinking. Good work.

Re: Hand Crank Grinder Conversion

#3

Re: Hand Crank Grinder Conversion

Mike Fitterling

>Nice Todd. Looks handy. Is that your pit saw on the left? Tried sharpening it yet?

Re: Hand Crank Grinder Conversion

#4

Re: Hand Crank Grinder Conversion

Ernie Miller

>That is prety neet send me one of them will you? What did you use to ease the edges in that plywood a spoke shave? I like you having camera capabilites you can post some of your dinking around.

Re: Hand Crank Grinder Conversion

#5

Nice set-up Todd-O ...

Raymond in Trenton, NJ

>And thanks for the pic. How about a side view please, where the grinder clamps on? I'd like to borrow your "Yankee Ingenuity" for my own grinder :o) That's a clever idea in getting around the limited clamping on most grinders I've seen.

Raymond

Re: Hand Crank Grinder Conversion

#6

Re: Nice set-up Todd-O ...

Todd O. Cronkhite Maine Native in FL. Exile :~(

>Patrick,

Sure beats Better Living thru Chemistry eh? :~)

Mike,

Yup, that's the Japanese Rip saw, and no I have yet to attempt to sharpen it, and have no intentions of doing so. The more I think about the less I like the idea of ripping out beams/slabs etc, etc. I think that splitting the log in half than flattening it from there is the better way to go, besides I really never work with wood of that size anyhow. I do have one log that I split in half last year with the intentions of using my adz to flatten it, but have yet to get to it.

Ernie,

No wise arse, I didn't use a spokeshave on that plywood, I used a rasp. Yes, being picture capable sure is neat, don't expect to see anything magnificant tho as at this point all I do is dink around. Right now I'm dinking with a new tool chest idea. It's all found plywood, 2x4's and drywall screws right now, but that is because it is a prototype. If it works out as planned than I'll remke it out of better woods someday---maybe. ;~) At least this chest will provide a decent home for my LN's so I can get them out from under my bed. I think some of them have been there since '98 or '99. :~( The inside demensions of the drawers are 26"x33&11/16. they all will be of varing depths which will be determined by the particular tools that I intend to put in it. The runners will be found angle iron. Big drwaers to be sure, but by making them this size I believe that it'll allow me to keep the chest low enough to fit under the new low workbench I am intending to build. My current bench is too high for some operations.

Ray,

OK I'llpost more pictures either tonight or later in the week. I'll take it apart to show more construction details. Feel free to "borrow" any of my idea that you can.

On a side note, I really hate the word "clever". I had a buddy--notice I said the word "had" as I cannot stand that guy anymore-- whom when growing up was the apple of his mothers eye. He could do no wrong, but he was a true devil. She always bragged about how clever he was. Well, the only thing he was clever at was pulling the wool over her eyes by making her think he was a saint. Yeah, real cleaver.

Todd O.

Re: Hand Crank Grinder Conversion

#7

Re: tool rest

Moses Yoder in White Pigeon, MI

>I love seeing these old grinders put to use. You just can't beat them for use in a wood shop. I used to use a shop built rest, but in one of my moments of better judgement bought myself the Veritas rest for Christmas. It is about $35 I think, and have to say it is well worth the money. My tools may not be sharper, but the rest is much easier to use than my shop built version and also locks into position much better and easier. Maybe sell one of those stones and put the money to better use. Just a thought ;)

Re: Hand Crank Grinder Conversion

#8

Re: tool rest

Todd O. Cronkhite Maine Native in FL. Exile :~(

>Nay, nay Moses, no need for a fancy tool rest. I merely lay the bevel on the stone to the angle I want and than register it with my finger. As long as I don't move my finger I'm fine, and can regrind a new bevel lickety split. This technique also allows to to feel if the metal is getting too hot which is very very rare.

I had a LV adjustable tool rest and didn't like it one little bit. Just too fidgity to adjust.

Todd O.

Re: Hand Crank Grinder Conversion

#9

OK ... you're not clever ...

Raymond in Trenton, NJ

>I get the point. How about ingenious then? :o)

Re: Hand Crank Grinder Conversion

#10

Much Better Thanks! :~)

Todd O. Cronkhite Maine Native in FL. Exile :~(

>

👍 This page answered my questions

Your vote helps other woodworkers quickly find the answers and techniques that actually work in the shop.