Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Hand tools to the rescue!

Posts

Hand tools to the rescue!

#1

Hand tools to the rescue!

Stephen Kirk in Quakertown, PA

>I just have to post this, since it seems I'm being steadily forced onto the handtool path. I'm building a new bench, and I was ready to rout out the pocket for the face vice to sit in. I set up the router, checked my max plunge depth, marked out the waste area, put on my dust mask, put on ear protection, plugged the tool in, flipped the switch, and ... nothing. 1/2 hour of putzing with the router to try and clean out the switch and I may have broken in further.

So, I figure, I'm starting to use hand tools more, so lets see what I can do. I have a little Craftsman dovetail saw, and a set of Craftsman chisels that I put a good edge on. I was able to make several cuts along the edge of the bench to outline the notch, and then just started tapping chunks out with the chisel. Took about 45 minutes, but if I knew what I was doing, probably would have been 10 minutes or so.

Now to resharpen, since the laminated MDF probably dulled up the chisels pretty good. Just thought you all might like another hand tool rescue story.

Re: Hand tools to the rescue!

#2

Re: Hand tools to the rescue!

Bill Houghton, Sebastopol, CA, gettin' soggy

>Like a lot of us on this forum, I'm a hybrid user - I use tools powered by both electricity and cholesterol. One of my lessons of the past decade has been that there are times when a sharp edge is MORE efficient than a power tool.

While that may have taken you longer than the router, you avoided operating in a cloud of fine dust, too (I still remember the first time I routed MDF - I thought I'd been transported to a flour mill during an explosion).

Congrats on your slide down the slope.

Re: Hand tools to the rescue!

#3

Re: Hand tools to the rescue!

frank shic (walnut ck, ca)

>stephen, nice job stud! i did the same thing when i was installing a quick release vice in the tail end of a pine countertop i bought from home depot. i contemplated using the router for a second and then thought, "hey, why not let this opportunity serve as my BAPTISM into the cordless world?"

Re: Hand tools to the rescue!

#4

Jack Guzman from Maine

Re: Hand tools to the rescue!

Jack Guzman from Maine

>Congratulations Stephen. Next step is to get away from using that nasty compressed dust as a substitute for wood.---Jack

Re: Hand tools to the rescue!

#5

Re: Hand tools to the rescue!

Stephen Kirk in Quakertown, PA

>I used the MDF to save myself quite a bit of money building the top. Unfortunately, then you have to laminate several sheets with contact cement, which is some particularly nasty smelling stuff. Makes for a flat, really heavy top, though.

Re: Hand tools to the rescue!

#6

Re: Hand tools to the rescue!

Stephen Kirk in Quakertown, PA

>Oh yeah, I had cleaned the edges up with the router when it was working. That is some super fine dust, and I was just coated. I would sweep and vacuum after each routing session.

Now all I have is a little dust, and a bunch of chips.

Re: Hand tools to the rescue!

#7

Way to go!

Scott Burr in rainy Ben Lomond,CA

>Personally I'd never let my hand tools touch MDF let alone myself;^)

Congrats on learning something new!

Re: Hand tools to the rescue!

#8

Re: Way to go!

Ted Owen, Pittsburgh

>Same here. That's what hardware store cheapies are for.

Best, Ted

Re: Hand tools to the rescue!

#9

Re: Way to go!

Stephen Kirk in Quakertown, PA

>None of my tools are exactly expensive, high end items. But hey, we all gotta start somewhere. The MDF will make a decent bench that should last long enough for me to consider another top. I just didn't have 6 months of leisure time to build a solid wood top (or the money, actually). This will be my indoor bench, so it'll be hand tool work only, and how I hope to get some practice during the cold winter months.