Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Veneering ? PIC

Posts

Veneering ? PIC

#1

Veneering ? PIC

Larry in Ohio

>I tried posting this question on the main board, but didn`t get any answers, so it was sugested to try here. From the Pic you can kind of see what I`m trying to do. The "FRAME" of the coffee table top is 1"x21/2" with a 1/2" lip where the 1/2" plywood lays on. On this is the 3/16" or less, depends how it all sands out. It`s going to be the same on the other side, and in the center will be a piece of very curly dark walnut. The questions are what kind of glue should I use? Will my trusty ole yellow titebond work? Also will I have much of a problem with the expansion and contraction, if so what can I do to solve it. Many Thanks. Larry


img

Re: Veneering ? PIC

#2

Re: Glues

John in New Mexico

>Hi Larry,

I'm not much of a veneering expert, but I've a bit of experience with several of the readily available glues for it.

My first choice would probably be plastic resin glue, like the brown Weldwood powder. I've used this stuff quite a lot for curved laminations. The main challenge I've had with it is getting the mix just right. Too much water is fatal, the veneer sticks, more or less, but you get a weak bond and the glue is kind of powdery when dry, leading to edges coming apart. Best bet is to mix by weight rather than volume, or to use the largest volume measuring vessel appropriate for the amount of glue you're making. You'd also need the ability to put a lot of pressure on the piece, which can be difficult with large flat pieces. Thick cauls and lots of clamps are needed.

I've used both Tightbond II and III straight from the bottle, applied with one of those cute little foam rollers from HD (as with the plastic resin glue). Again many clamps and cauls are the rule. This route seems to be a bit more irregular to me, as sometimes I get no warping at all (usually on plywood), sometimes I've gotten a truly frightening warp, easily cured (after initial panic) by veneering the oposite side, and once, way back, we had a horrible time with bubbling under the veneer (paper-backed, applied in vacuum bag).

I also once tried the old method of applying an even coat of yellow glue to both surfaces, letting it dry, and then ironing it on. It seemed to me to work well, as long as you diligently chase down and iron out all the bubbles. It's certainly the easiest method. I was using 1/16 cherry veneer over plywood, and had no long term warping problems, but did have a bit of trouble with the veneer shrinking and splitting a bit. Perhaps that is because the panels went un-finished for well over 6 months after installation. Maybe someone else has some insight or extensive experience with this technique.

Lastly, I'd probably try hammer veneering with hide glue. It's the old stand-by, many people swear by it. Easy to fix, though like the plastic resin, there is supposed to be a bit of a learning curve with it. I've certainly grown to prefer hide glue for joint assembly, as I find it's nice and slippery, so tight joints seem to stick less than with yellow glue.

Thats my 2 cents worth, I hope there's something in there that might help you out.

Good luck,

John

Re: Veneering ? PIC

#3

Re: Glues

Larry in Ohio

>John Thanks for the reply. Got some ideas. What I planned on doing was to glue, with titebond, 4 pices at atime and clamp the devil out of them and let set overnight, and then clamp 4 more. Why I would like to use the ole Yeller because I just don`t care to mix if I don`t have to. Also the pieces should end up being a good 1/16"+ after I get it sanded. Comments or ideas Larry

Re: Veneering ? PIC

#4

Hide Glue

ron in Kokomo

>I have used this stuff several times and I like the results

Re: Veneering ? PIC

#5

Re: Veneering ? PIC

Doug in Leawood KS

>Hi Larry,

I have veneered acres (well, a LOT anyway) with Titebond. It will be fine. So is Elmer's white glue, hide glue, and just about anything sticky. Just be sure and veneer both sides, even if the bottom veneer is commercial-thickness poplar, etc. And if you don't have any veneer tape, get some to hold the pieces together while you clamp. I use two layers of 3/4" plywood or MDF above and below the veneer sandwich, and one sraight and one curved batten for clamping.

Doug

Re: Veneering ? PIC

#6

Re: Glues

Tom Colligan, Peoria

>John, thanks for your input. Though you're not an 'expert' you know more than most. Can I use the liquid hide glue commonly sold by Franklin for veneering? And would this involve covering both sides of the veneer as well in order to lubricate the visible side while hammering? Thanks again.

Re: Veneering ? PIC

#7

Re: Glues

Dan Donaldson

>I don't believe that you can hammer veneer with the liquid hide glue. You need the hot kind for that.

Re: Veneering ? PIC

#8

Re: Veneering ? PIC

Mark Harrison -- in Sydney, Australia

>I've given up on veneer tape. I use ordinary clear packing tape instead. I otherwise agree with you though.