Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

Garrett - Work Knife Replacement

Posts

Garrett - Work Knife Replacement

#1

Garrett - Work Knife Replacement

Bob Smalser, Seabeck, WA

>

I use a knife several times a day on the job that involves a lot of tree work, excavation and heavy construction. Much as I love the automatic Buck, it’s just not tough enough for the job, and I decide to replace it with a fixed blade. So I start looking for rigging knives…short, thick, and tough enough to hit the blade back with a hammer. Put off by the 100-dollar-plus price of the better ones, I looked around for older, used knives to grind down, but couldn’t find one with a thick enough blade. Retired shipwright Dave Fleming was nice enough to go around to marine stores and handle a bunch of them…and recommended the Linder in the 60-dollar range. So I ordered one.


Great knife and perfect for my needs…. but the sheath at top left that came with it wasn’t made for that knife…. way too tight and the knife rides backwards for a right-hander. My usual trick of building up the knife handle with foam and tape, soaking the sheath and letting them dry out while mated didn’t work. The chrome-tanned shoe leather didn’t stretch and mold itself around the knife. Oh well…the sheaths for my Buck and multitool have seen better days, and I recently lost my Maglite sheath…so I’ll simply have to make a new one that accommodates all my usual side arms.


I make a pattern out of graph paper, puzzling out all the tool pockets and seam allowances by trial fitting, snipping and cutting….


…and when I’m satisfied I won’t ruin any expensive leather, cut the pattern out from vegetable tanned tooling leather, which will stretch and shrink very forgivingly to accommodate my guesses on sizes and seams.


As I’ll carry this all day, every day, I want the tools mounted relatively high on my belt so they don’t gore me sitting in the truck, and I want the sheath to tip forward a bit…so I position the belt slide on the back of the sheath accordingly. I use a pounce wheel to mark the seams for even stitches.



On the front of the sheath I’ll mount my multitool…I lay out an applied pocket…


…and stitch it on with lock stitches using a harness stitcher. I could also use the sewing palm and sail maker’s needle to make lock stitches, but the harness stitcher is easier.

Continued….

Re: Garrett - Work Knife Replacement

#2

Re: Garrett - Work Knife Part II

Bob Smalser, Seabeck, WA

>

To protect the interior stitching from the knife blade, I rub them into the leather with a seam rubber and douse them in cyano glue for a little armor.


I make a spacer of thicker leather for the back seam, and will awl holes for that seam, as accurately aligning 4 thicknesses of leather for stitching requires it. I pounce and awl the sheath’s front first….


…transfer those holes to the thick spacer with the aid of lofting ice picks for alignment…


…and finally to the rear of the sheath. I trial fit my tools as I go and decide to change the shape of the Maglite and fid pockets, as I have more leather there than I need.


When satisfied with my final shape, I’m almost ready to stitch the main seam.


As I will rivet the point of the seam’s main stress, I punch holes and use the rivet’s copper nail as an alignment aid instead of an ice pick. With awled holes, alignment is easy and I complete the seam, doubling my stitching at stress and wear points.


Then all that remains is finishing the rivet and stitching out the fid/Maglite pockets…


…soaking the leather and fitting the tools to the sopping wet sheath…including the belt in the belt loop. It then goes on a high shelf above the radiator to dry and shrink.

Continued…

Re: Garrett - Work Knife Replacement

#3

Re: Garrett - Work Knife Part III

Bob Smalser, Seabeck, WA

>

After the soaked leather dries under heat, shrinking around the tools, I evaluate the fit for final corrections.

I wet it again...this time with alcohol...lightly where the fit is good and heavily where I need more molding....and I "bone" all the seams and the moldings with hardwood for a better fit and finish.

Then I strap the still-wet assembly on the belt and wear it for a day to further mold it to my body.


I could have tooled the leather with fancy designs….and I could finish it the typical way with dye followed by lacquer…but as all these leather utility items will wind up looking like the original sheaths above within a year, I choose a utility finish.

Examine antique, tooled leatherwork finished with lacquer or oil and you’ll find a lot of dry cracked leather. Much of that is the quality of the leather used, but the oldest leatherwork I’ve seen that was still in service after many decades was Swiss…and I duplicate that finish by saturating the leather in melted beeswax. The sheath is left in the hot wax just long enough for the leather to heat sufficiently to allow the wax to penetrate to the core…then removed and cooled.


Then for cosmetics, I buff it out with an old-T-shirt rubber, water, and a light coating of harder carnauba wax atop for a “spit-shined” finish.

That’s the last maintenance I’ll have to do to that piece until it wears through, and I save the pattern for when that day comes.

Re: Garrett - Work Knife Replacement

#4

Re: Garrett - Work Knife Part III

Todd Stock

>I've had a Linder since 8th grade, and never thought to build a workable (one-handed, even when the leather is soaked) sheath for it - nice work.