Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

anyone see graham blackburn's video?

Posts

anyone see graham blackburn's video?

#1

anyone see graham blackburn's video?

frank_shic

>i just recently got the graham blackburn video on making raised panel doors and was completely FASCINATED with the idea and safety of crafting them by hand - i'll admit that i'm TERRIFIED of my router when it's spinning such a huge chunk of metal at such high speeds!

that being said, what kind of plane is he using to cut the dados for the rails and stiles? is it a tongue and groove plane or a combination plane? in my continuing quest to acquire all the handplanes that i will ever need in as SHORT of time possible, i need some of your sagacious wisdom!

Re: anyone see graham blackburn's video?

#2

Jack Guzman from Maine

Re: anyone see graham blackburn's video?

Jack Guzman from Maine

>I'm not sure about what Blackburn used but I use a plow plane to cut the groove for the panel.---Jack

Re: anyone see graham blackburn's video?

#3

like a stanley 45?

frank_shic

>

Re: anyone see graham blackburn's video?

#4

Jack Guzman from Maine

Re: like a stanley 45?

Jack Guzman from Maine

>yes,or a 44,or any woodie plow.(there are more)--Jack

Re: anyone see graham blackburn's video?

#5

another QUEST begins!

frank_shic

>thanks for your input, jack! one more question for you: how do you get the curved profile that you commonly see on router made rails and stiles? do you have to use a moulding/molding plane to shape it after plowing the dados?

Re: anyone see graham blackburn's video?

#6

Jack Guzman from Maine

Re: another QUEST begins!

Jack Guzman from Maine

>Yea,I guess you could call it another quest.More like a slippery slope.Molding planes.There are alot of variations.I don't put a profile on my frames,at least I haven't yet. I leave them square. I like simpler frame and panels than what you get with power tools/modern designs. If I was to attempt a profile then I would need a molding plane/planes or a scratch stock.---Jack

Re: anyone see graham blackburn's video?

#7

would a stanley 48 work?

frank_shic

>i've noticed that the stanley 45's are going for pretty top dollar but the stanley 48's are much more affordable.

Re: anyone see graham blackburn's video?

#8

Yes, but

Jim Reed @ Tallahassee

>only within limits. It would work pretty well for 3/4" stock where you need a 5/16" groove down the middle. Plow gives you more flexibility on where the groove goes.

Re: anyone see graham blackburn's video?

#9

Jack Guzman from Maine

Re: would a stanley 48 work?

Jack Guzman from Maine

>Look for an 044 record. They're pretty common on ebay,go for cheap money and easy to use.---Jack

Re: anyone see graham blackburn's video?

#10

Re: would a stanley 48 work?

Moses Yoder in White Pigeon, MI

>The #46 is a skewed plough plane; so it should work better than the 45. I still have to try out mine. If you can find a 46 it would be a good plane to have. The #50 is a simpler and lighter plane that works pretty good. Or of course also as Jack suggested, a Record of Craftsman combination plane goes wuite a bit cheaper than the Stanley and is essentially the same thing.

Re: anyone see graham blackburn's video?

#11

thanks guys!

frank_shic (walnut ck, ca)

>jim, thanks for reminding me about the size of stock constraints on the tongue and groove plane. jack, i appreciate the advice on the record 44's - they're much SHINIER than the stanley's! and moses, i'll probably start watching out for the 46's as well.

slip sliding away...