Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Wooden Lathe

Posts

Wooden Lathe

#1

Wooden Lathe

Piccini Gabriele

>Hi All,

I'm new and I'll be a great "questioner" because I haven't a lot of experience about woodworking.

Well, I wish to ask to All if someone has never built a wooden lathe, both pole and treadle.

It it is, I'll be very concerned to know the trouble occurred during the conctruction.

Re: Wooden Lathe

#2

Re: Wooden Lathe *LINK*

Greg B�tit, Vergennes, VT

>There is a tremendous amount of information On the net written about this subject. Do a "Google" search for "pole lathe" or "treadle lathe" to get started. The link included below is one that will pop up, and is a good place to start. At this site, among other things you will find information about Roy Underhill, who has featured his pole lathe on his Public Broadcasting System series as well as in at least one of his books.

My advice is to build your lathe very sturdy. I built one a while ago which was designed to be portable, but unfortunately it was not able to withstand the repeated reversing forces a pole lathe experiences. After a few days of frustrating use I took it apart and used it for firewood.

Greg


Pole Lathe FAQ

Re: Wooden Lathe

#3

Re: Wooden Lathe

Bob Hackett

>The AAW had an article in the journal about a foot powered lathe that used a ratchet mechanism to power the wheel.A turning club made it and used it for demos.

FWW also had an article on a footpowered lathe that incorporated the drive from a bicycle wheel and was in use at a HS school WWing program.I believe the same article was also in the Making WWing Machines book.

Albert LeCoff at the Woodturning Center in Philadelphia PA is also a great resource for solving problems related to woodturning and maintains an incredible library on woodturning.He`s the go to guy to get good info and contacts.

Last but not least the folks over on the turning board have extensive knowledge on this subject.A search of the archives would be a good starting point.

Mainely,Bob

Re: Wooden Lathe

#4

Re: Wooden Lathe

Warren in PA

>Some years ago I worked at a historic site where I demonstrated on an old (1804) treadle lathe. Because it was old and worn, there were minor problems with the bearings and the pulley that cut down on efficiency and quality. I later built a pole lathe because there were many fewer technical issues to worry about.

I must say I was shocked at how well the pole lathe worked; the second day I was turning better than I had with electric or treadle lathes. Some people use springs or bows etc. rather than a pole and I've tried some of these and a bicycle wheel type. I think you would be happiest with a pole.

If you have means to make or buy make the special hardware for a treadle lathe, the advantage of this type is more versatility.

Re: Wooden Lathe

#5

Re: Wooden Lathe

Mike Jurnigan

>I have an old treadle lathe. Circa 1870-1880. I am willing to photograph it and provide you with dimensions and advice based upon my use of the lathe at various demonstrations that I have done with it. E-mail me or call me at 757-657-6818.

Re: Wooden Lathe

#6

Re: Wooden Lathe

Piccini Gabriele

>Hi Mike,

I'll be very happy to see pics about your lathe.

Naturally I do not want to create much disturbance to you.Many thanks.

Re: Wooden Lathe

#7

Re: Wooden Lathe

George Makowski

>Hi Gabrielle, I built a pole lathe long ago based on information in the Foxfire books. Instead of a pole, I used strips of inner tube tied to the rafters of the garage. It was rough with the ways and poppets out of 4x4. One end was connected to a built in work bench. The adjustable poppet was fastened by a wedge and mortice. The centers were 3/4" square pieces of iron filed to cones to take the work. I told you it was rough! All the same, even with minimal tools, I was able to turn and repeat shapes to 1/32". I made some tool handles, tuning pegs, and a mallet as well as practice pieces. The reciprocating motion is much less of a problem than you would think.

So, check out the Foxfire series, the pole lathe articles appear somewhere in the first couple of volumes and see, of course, Roy Underhill's work. There is also lots of good web information from the UK where pole lathe turning has become an important part of the folklife and sustainable development world.

Good turning,

George in AL