Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Cleaning up bed in wooden plane construction

Posts

Cleaning up bed in wooden plane construction

#1

Cleaning up bed in wooden plane construction

Peter Michaux

>Hi,

I have read David Finck's book on making Krenov style planes. I'm curious how people clean up the bed of the plane. David's method is to cut the basic angle of the bed on a band saw and then use a block plane to clean up the bed. Any other suggestions?

Thanks!

Peter

--------------------------------------------------------------------------------------------------------

What I've learned about sharpening plane blades

http://members.shaw.ca/petermichaux/workshop/BevelDownSharpening.html

Re: Cleaning up bed in wooden plane construction

#2

Re: Cleaning up bed in wooden plane construction

Richard R

>Peter,

You could use a disc sander, if you have one. However, I'd advise against looking for a different/better way to true up the bed. I picked up David's book a couple of years ago. I've only made one plane so far (a jack), but it works just fine (I actually used it to flatten a table top for a commission). The process of squaring up the bed is really very easy. The piece is so small, I think it may have taken about 5 minutes with my 102 and an engineer's square. Just go for it! Worst that can happen is you'll lose a tiny bit of length from the back of the plane if it takes a few tries to get it right...

RR

Re: Cleaning up bed in wooden plane construction

#3

Re: Cleaning up bed in wooden plane construction

Steve Knight

>well it depends on how you cut it out. I use SCMS and it is pretty accurate. but a tablesaw would work well too. as long as the cut is square it's easy. I just lap the surface on my big surface plate. but you need to make sure the cut is very accurate. this has been a battle of mine. always check to make sure if you ahve to squaite it up you can do that by lapping it but it is pretty slow going.

I am lucky if it takes 10 or 20 seconds to get it up to par. to make the cuts on the miter saw really accurate I use some good flat plywood under the plane body before I cut it.

Re: Cleaning up bed in wooden plane construction

#4

Re: Cleaning up bed in wooden plane construction

Moses Yoder in White Pigeon, MI

>I would kind of question if you are ready to build and use a wooden plane if you are not comfortable with using a block plane. A mitered end grain is fairly easy to cut with a block plane. You have to make sure you are planing with the grain and not against it.

There are a number of ways you could flatten the bed after cutting it. You could even rig up some sort of gizmo to lock it into position and then use a router with a straight bit to trim it. Rube Goldberg would be proud. The disc sander has been mentioned, and would work well if you have a flat back behind the disc. Steve's suggestion of lapping would also work well if the initial cut is accurate.

Re: Cleaning up bed in wooden plane construction

#5

cut and plane

bill tindall

>I cut it on my chop saw and adjust if necessary. I have done it on band saw and planed smooth too.

In any case it nees to be flat and square to the sides.

Re: Cleaning up bed in wooden plane construction

#6

Re: Cleaning up bed in wooden plane construction

ThomD

>THe blck plane works great, IF you have one that is tuned or was properly made in the first place; and, if you have good solid vice. Cutting the block on the table saw, etc... is fine, and it can be made safer, if the pices you are cutting is long enough, it can be a real dangerous cut if you just have a small piece. A slick works well too.

One should also be able to cut it freehand with a hand saw.

The problem is starting out. I made my first Krenov style plane years before I had any decent tools, and I just had to figure out what would work from the junk I had to work with.

Re: Cleaning up bed in wooden plane construction

#7

Re: Cleaning up bed in wooden plane construction *LINK*

Philly

>Hi

I just made my first wooden plane (following David's book) I cut the bed on my Unisaw using an Osbourne mitre gauge. No clean up was necessary. This was an easy way to accurately make the pieces-just use your best blade for a clean finish!

Incidently-the cheeks of my plane were made from MDF (it was for a competition to make a project with man made materials!!) Here's a picture....

Hope this helps,

Philly


img

http://www.philsville.co.uk