Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Wooden spokeshave's gettin' loose - easy fix?

Posts

Wooden spokeshave's gettin' loose - easy fix?

#1

Wooden spokeshave's gettin' loose - easy fix?

Scott in Douglassville, PA

>Hey, everyone -

I have an old wooden spokeshave (the iron's tang-fitted) that's getting loose. When in use, if the iron catches, it pulls out as often as not.

I like the thing, and would rather rehab it than replace it. Is there a way to tighten it up that is idiot-proof enough that even I could do it? I'm figuring that this'll involve tightening the tang mortises (terminology?), but any experience would be helpful...

Thanks,

Scott, playin' on the new shaving pony

Re: Wooden spokeshave's gettin' loose - easy fix?

#2

Jim in Burlington Ont.

Re: Wooden spokeshave's gettin' loose - easy fix?

Jim in Burlington Ontario

>Couple drops of CA glue in the tang holes. If that's not enough a little bit of epoxy will do the trick.

Re: Wooden spokeshave's gettin' loose - easy fix?

#3

Re: Wooden spokeshave's gettin' loose - easy fix?

Bob Hackett

>How do you adjust after glueing the tangs in?

The quick fix I`ve always used is to shim the tangs with either tiny wood wedges or cardboard shims.These fixes allow for adjusting the blade and removing it for sharpening.

A friend had some luck bowing the tangs alittle over the jaws of a vice.I prefer not to tempt fate by taking a hammer to an old blade.

The long term fix is to either make a new body or plug and redrill the old holes.

Mainely,Bob

Re: Wooden spokeshave's gettin' loose - easy fix?

#4

Re: Wooden spokeshave's gettin' loose - easy fix?

MikeS

>Historical fix was to wrap a thin shaving around the tang, I think.

Re: Wooden spokeshave's gettin' loose - easy fix?

#5

Paper

Pam Niedermayer - Austin, TX

>When Japanese planes and irons get loose, we insert paper. In your case you could wrap the tang easily. When they get too loose for paper, time to make another dai.

Pam

Re: Wooden spokeshave's gettin' loose - easy fix?

#6

Re: Wooden spokeshave's gettin' loose - easy fix?

Todd Hughes

>Judging by all the ones I see in the wild the traditional fix for this was taping in small nails or tacks to wedge the tangs in place. I have used shaves like this and they worked fine. Personaly if I was going to use it much I would glue in a sliver of wood to close the hole up some. Would for sure NOT glue the tangs in....Heck you might want to sharpen it sometime !....Todd

Re: Wooden spokeshave's gettin' loose - easy fix?

#7

Disappointment

Bill Houghton, Sebastopol, CA

>I opened up Todd's post, looking forward to how he resolved this problem by careful application of a shotgun, only to discover that he's talking about gluing in little slivers of wood! My day is ruined.

Re: Wooden spokeshave's gettin' loose - easy fix?

#8

I *think*...

Scott in Douglassville, PA

>...what Jim was suggesting wasn't gluing the tangs in place. I think that he was suggesting dropping a little CA in the holes, letting it harden, then replacing the iron. The hardened glue would provide a very small constriction in the hole, helpig the friction fit.

I could be wrong - has happened before... ;)

Re: Wooden spokeshave's gettin' loose - easy fix?

#9

Re: Disappointment

Todd Hughes

>Speaking of shot guns ,...Well will tell you that "gluing in little slivers of wood" probably won't work on that stray cat that had taken to messing in my shop...Todd

Re: Wooden spokeshave's gettin' loose - easy fix?

#10

Wait a minute!

Bob Hackett

>Don`t tell me you`ve spoiled your dogs to the point they will only eat UPS employees now!

MB

Re: Wooden spokeshave's gettin' loose - easy fix?

#11

Jim in Burlington Ont.

Re: I *think*...

Jim in Burlington Ontario

>Thanks no don't glue them in there just a little drop wait till it dries and your back on track quickly.

Re: Wooden spokeshave's gettin' loose - easy fix?

#12

Re: Wooden spokeshave's gettin' loose - easy fix?

Alice Frampton, UK

>A traditional solution is to put a screw in from the back, one to bear on each tang. Tighten them up to hold the blade, loosen them when you need to remove it. Simple.

Cheers, Alf

Re: Wooden spokeshave's gettin' loose - easy fix?

#13

Success!

Scott in Douglassville, PA

>Thanks for the input, everyone. When the iron pulled out again, I ran a small shaving in alongside the loose tang. Tapped it back in, and it's holding well. I figure this is a temporary fix; when the time comes, I'm gonna try dropping a little CA in the hole. I really like the ability to set the iron with a tap or two - screws would wreck that. Plus I'm sure I'd booger it all up...

Thanks again.

Scott