Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

No. 4 Fulton Smoother problems

Posts

No. 4 Fulton Smoother problems

#1

No. 4 Fulton Smoother problems

Charles McKinley

>Hi All,

I spent the better part of the other night flattening and honing the iron for this plane and now I can't get the adjustment right. When I bring up the blade it doesn't cut at all and when I lower it it digs in. I'm new to this but have set up a couple on No. 5s.

The adjuster seems to barely contact the slot in the chip breaker. I think this is where the backlash is as the forks on the adjustment knob fit quite well. Is there a way to improve this adjustment or do I send it back to ebay from whence it came and start on another smoother? I would hate for another beginner to get it and think all hand planes are like this.

Thank you for your help,

Chuck McKinley

Re: No. 4 Fulton Smoother problems

#2

Re: No. 4 Fulton Smoother problems

Dale Stansbery

>Chuck,

It sounds as though the leading edge of the mouth could still be too high, hmmm, or would that be low. Anyway, when you flattened the sole, did you mark the leading edge of the mouth with a felt tip, and make sure the mark was being removed by the flattening. A lot of old heavily used planes have visibly worn leading edges. That can help create the symptoms you mention. I only have one Fulton, a number 3 that I never could get the sole anyway near flat on. In hindsight, I now wonder if the castings are harder and don't sand as easily as a Stanley. Anyway, I opened the mouth with a die grinder, re ground the blade into a scrub profile. It works great.

Re: No. 4 Fulton Smoother problems

#3

Re: No. 4 Fulton Smoother problems

paul womack

>When I bring up the blade it doesn't cut at all and when I lower it it digs in. I

There are 2 potential causes of this symptom

* A concave sole; the blade is in mid-air, until you lower it enough to "bite". The entire plane then flexes DOWN into the workpiece, This is unlikely with a #4, since it's relatively stiff (due to short length).

* A poorly bedded blade. The blade is not fully bedded; you lower the blade (deepen the cut) until the blade bites; the blade is then slammed down onto the bed, deepening the cut further.

If you're really unlucky you could have both causes :-)

BugBear

Re: No. 4 Fulton Smoother problems

#4

Exactly...

WoodburnBob

>...and perfectly stated.

I don't know if Fulton is one, but many of the makers of Bailey knock-offs, seemed to pattern their products on a frog design that left the front half of the frog unsupported, suspended in the air. In effect, it was a sort of diving board arrangement.

Even Stanley in their late-style Defiance planes offered such a frog-bed arrangement. These late-model Defiance planes are a great bargain for the novice tool-guy, unless he actually wants to use them to plane wood. But they are generally in really great shape, as if they just emerged from a time capsule. No wonder. They were never used.

A few times with this sort of plane, I've tried shimming the front of the frogs with various substances and it can be done. They can be made to work. But in the universe of first class $30 Baileys and $90 Bedrocks, what's the point...other than passing time on a Saturday afternoon.

Something worth doing with any plane that performs this way is to loosen the screws holding down the frog until the tension is off. Then see if you can rock the frog to and fro on its bosses, its foundation. If the frog rocks, that may be part of the source of the problem also.

Re: No. 4 Fulton Smoother problems

#5

Re: oops...

paul womack

>reading your post, I realised that I missed one.

I mentioned concave sole, and poor blade-to-frog bedding, but missed poor frog-to-sole bedding.

BugBear

Re: No. 4 Fulton Smoother problems

#6

Thank you very much!

Charles McKinley

>I will try your suggestions and may end up making a scrub out of it if all else fails as I don't have one yet and it is to ugly to use as a paperweight.

Chuck