Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

Straightening HSS tools

Posts

Straightening HSS tools

#1

Straightening HSS tools

Sandor in Boyds, MD

>I picked up a 1/16" x 3/8" lathe parting chisel today made from HSS. Upon closer examination, it is bowed from the tip to the hilt. About 1/8" on 7"

Since HSS is pretty brittle, does anyone have a recommendation for (or experience with) bending this material? I have visions of snapping the tool in half if I try brute force persuasion. Can I get it cherry red and then bend it?

Thanks,

Sandor (I know it's a lathe tool, but this is more of a chisel question...)

Re: Straightening HSS tools

#2

Re: Straightening HSS tools

Bob Hackett

>Evidently someone got carried away and was alittle too far over the toolrest.

I`ve had good luck straightening HSS by just clamping the end in a vice and carefully pushing on the handle.I figure if it bent one way it should bend back.Grind and polish any dings or dents first and keep all body parts behind the handle and well away from the shank just in case.

An alternative method has been to lay the chisel on a hardwood block and straighten using a mallet.

I`m going to play an angle that I learned here and ask if you`ve used it first.Try it,if there`s only a slight bow you may find it`s no big deal!

BTW-the only type of HSS I wouldn`t try these things on is particle steel.Bill Tindal`s 3V steel may bend but I`ve seen 3 broken Glaser gouges(good steel,bad turners)and a British scraper broken off in use.Makes me believe they don`t take well to bending.

Mainely,Bob

Re: Straightening HSS tools

#3

maybe a hijack, but still in hand-grenade range...

John Truxell-Svenson (jvs)

>Bob (or anyone else), I have a PSW socket firmer that has a "curl" from the pointy end back about 1 1/2" up the shank, but still ~4" of hard steel after that. I was tentatively thinking about clamping it braced against the bend for a few days, but do you think the mallet idea would work for laminated steel, too? The condition I got it on was pretty rough (rust, mushroomed socket, since ground off, etc.) so no huge loss if it snaps--it would just turn into a "butt firmer" and go into the same rack.




/jvs

Re: Straightening HSS tools

#4

Re: maybe a hijack, but still in hand-grenade rang

Bob Hackett

>I`ve done just that to many bowed laminated chisels to hurry the flattening process.If the chisel doesn`t respond to tapping with a deadblow mallet over hardwood I sometimes go to a soft brass hammer with the chisel supported across the copper jaws of my metalworking vice.

The process is about two steps more agressive than tapping out a japanese plane iron which is a real nail biter.So far I`ve only lost 1 chisel,a Charles Buck that I think was cracked when I got it judging from the fracture.

Mainely,Bob

Re: Straightening HSS tools

#5

Will likely snap

bill tindall

>Most common HSS lathe tools are M2. We got in some unhandled M2 skews and the tangs were not in line with the blade. Not to worry we thought. Put in vise, heat to red hot(about 500 degrees too cool to have worked as it turned out) and pound upon with large hammer. Snapped the tang right off.

M2, we now know, is tempered up around 1000 degrees so it must be heated hotter than that to soften it.

If the tool is M2, and you must straighten it, take it to heat treating place. They will reheat, straighten and retemper. Paul Bos will do it for about $15.

Re: Straightening HSS tools

#6

worked like a charm--thanks!

John Truxell-Svenson (jvs)

>

Re: Straightening HSS tools

#7

Re: Straightening HSS tools

Todd Hughes

>I have straightend items like this ,[mostly knives] by using a vice and 3 dowels.Have also snapped them but i think it is safer then beating with a hammer or bending by hand. What i do is put the blade in a vice with 2 wooden dowels on the side away from the bend and then the third dowel right over the bend then tighten the vice till the bend is taken out.I go a little past this and then leave it in the vice for a while though don't know if this does anything, probably doesn't but hey doesn't cost anything. I have had very good luck using this method but like said have also had the piece snap...it's a gamble....Todd

Re: Straightening HSS tools

#8

works as is, even with the bend

Sandor in Boyds, MD

>I tried out the parting tool last night and it works as is. The bend is gradual enough and far back enough that it won't matter on the stuff I turn - usually less than 3" diameter.

The bend just bugs me though...

But I think I will not risk snapping my very expensive ($1 minigloat) parting tool.

Thanks for the responses,

Sandor